Best Auto Body Shop in New Jersey

If you’re looking for an auto body shop in New Jersey make sure you give Peotters Tire & Auto a call as the New Jersey areas premier tire and brake shop. Today’s vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop in New Jersey to be aware of the different materials and techniques used for repairing them.

Auto body shops like Peotter’s Tire and Auto and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills.

A good, eco-friendly auto body shop in New Jersey will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

Today's vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop to be aware of the different materials and techniques used for repairing them.

Auto body shops and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills. A good, eco-friendly auto body shop will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part. Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part.

Tire City

Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.

Who Really IS the Best Auto Body Shop in New Jersey ?

Frame Straightening

Ever since mankind realized they could harness the power of horses and use this as a means of transportation there have been accidents.  Today we associate horsepower with motor engines and where once we had just a single, pair or team of horses providing the energy to move the vehicle, we now have the power of many hundreds of horses under the bonnet of the modern motor vehicle.  With this increase in power comes an inevitable increase in accidents and accidents invariably include dents.

One of the biggest issues facing someone who has been in a motor vehicle accident is the question of where and how to get their vehicle repaired.

Collision services are a collective body of services that assist motor vehicle owners in getting their vehicles back on the road after a collision.  It includes the after crash repairs offered by auto repair services such as repairs to the body of the vehicle ie dent and frame repairs and paint work.  Some auto repair shops work directly with insurance companies thereby reducing the need for the car owner to have to make too many decisions during what is often a very stressful time.

As with all these types of services, finding a quality, reputable company with qualified and experienced technicians to do the work is of paramount importance.  Dodgy work done by dodgy repair shops will not only end up costing you far more down the track when you inevitably have to get their repair work repaired, it may also be potentially dangerous.

Top Tips For Finding A Good Collision Service

Right at the top of the list is ‘ask a friend’.  Word of mouth and personal referrals have long been acknowledged as one of the most valuable, if not THE most valuable, forms of marketing in existence and there’s good reason for that.  It’s the one more people trust more than any other form of marketing.  So if you know someone who has been involved in a car accident and is happy with the repairs that were done on their vehicle and the customer service they received, ask them where they had the work done.  You can also ask local businesses in the auto trade if they have any particular recommendations or know of any reasons why you should maybe avoid certain repair shops.

Tip number 2 is to take matters into your own hands and conduct some one on one research.  Approach your local auto repairers and talk to them about the service they can offer and the guarantees they provide on their work.  Ask if they have photos of some of the work they’ve done that is similar to what you require and, most importantly, whether they have unsolicited customer feedback you can view.

And tip number 3 is that Google is often your best friend when it comes to research like this.  Look up local repair shops online, check their websites for photos and videos of their work and their customer feedback.  See if they have customer reviews on some of the big review sites like Yelp or, if they have social media pages ie Facebook, Google + etc, whether customers have left feedback there.

What You Need To Consider When Searching For An Auto Repairer

Not all makes of vehicles are created equal and not all auto repair shops can repair all makes of vehicles.  Therefore ruling out any who don’t deal with your make will narrow your search.

Which ones provide a warranty on their work, and how long is the warranty.  A warranty not only provides you with peace of mind, it’s also a good way of telling whether or not a repair shop has faith in their workmanship.  As a general rule, the longer the warranty period the more faith the repairer likely has in their work.  If you can find one that offers a lifetime warranty so much the better.

How are you going to get your vehicle to the repair shop if it’s too badly damaged to get there under its own steam?  If this is the case, you may want to find one that either has a towing service or can arrange for a towing service to get the vehicle to them.  Unless you have motor insurance or a motor club membership that includes towing.

How long can you function without a vehicle?  If you don’t have alternative transport and you rely heavily on your vehicle then you’ll need to find out how long each repairer estimates it will take them to fix it.  However, don’t sacrifice quality of workmanship for speed because chances are you’ll end up spending more time without a vehicle down the track when you have to take it back to have those hastily done repairs repaired.

And last but not least, getting back to word of mouth and doing business by personal recommendation.  Make a point of checking feedback provided by previous customers.

 

Auto Body Shops and Custom Work

Toyo Tires For Sale

What makes auto body shops so difficult to heat during the cold season? To shop owners, the answer is obvious. Auto body shops are characteristically dusty, breezy, high heat-loss environments. To make the indoor air more breathable and safe for workers, fresh air must be introduced through use of exhaust fans and/or raising overhead doors to help dissipate and eliminate contaminants. The problem is, as contaminants are pulled out, so is the heated air. Seemingly a "no win" scenario right?

So what's the most effective and efficient way to heat body shops?

Answer: Infrared radiant tube heaters.

Why Infrared?

To help answer that question, let's review what "infrared" is and how it works.

Infrared (IR) is electromagnetic wave energy that travels at the speed of light until it strikes an object. Upon striking an object, the IR energy converts to heat and is either reflected or absorbed. Dark and opaque objects (i.e. asphalt, concrete, etc.) readily absorb radiant IR heat energy, whereas highly reflective objects such as chrome and polished aluminum are poor absorbers and tend to reflect that energy away.

The most familiar IR emitter (heater) is our own sun. The sun radiates its IR energy through our atmosphere to the earth's surface, uninhibited by wind. As the earth's surface absorbs that energy, our air becomes warm.

During our North American winters the sun's rays are less dense due to the angle of the sun in the sky and our air temperatures are much cooler. But by summer solstice the sun's rays are at their peak angle and absorption is at its highest, resulting in warmer air temperatures.

Why use infrared tube heaters for your body shop?

1) Ceiling suspended infrared tube heaters mimic the warmth of the sun by warming up tools, machinery, floors and people directly, thereby warming the air indirectly.

2) Unlike forced air heaters, infrared tube heaters do not blow air throughout the space. That's a big plus in body shops where dust in painting areas is a problem.

3) Quicker heat recovery. As infrared energy absorbs into floors, tools, vehicles, etc., heat is recovered much more quickly when overhead doors are opened and closed again or when exhaust fans are cycled on and off periodically. That's because surfaces in the direct path of the infrared rays become a "heat sink". In other words, stored heat in objects re-radiates to warm the surrounding air.

4) Energy efficiency - an infrared tube heating system can save as much as 50% or more in fuel savings compared to conventional forced air. This is especially true in body shops where air exchanges are very high.

5) Infrared heaters can increase production. A carefully designed infrared tube heating system can be used to decrease drying times and enhance paint job quality. Placing vehicles in the path of infrared radiation warms cold metal surfaces. Paint applied to warm metal surfaces is less likely to run or drip than when applied to cold surfaces. And because infrared heaters don't move air around, there is less opportunity for dust particles to mix with newly applied paint.

We should note that gas infrared tube heaters are NOT to be used inside paint booths or paint mixing rooms. Tube heater emitters can reach 900 to 1100 Degrees F, well above the flash point of solvent-based primers and sprays. Spraying should be contained in a designated paint room with a filter bank and exhaust system to carry away potentially explosive fumes. Once spraying is done and the booth is ventilated with fresh air, vehicles and components can then be moved out of the spray booth to an isolated drying area where the infrared heaters are located.

Are some infrared tube heaters better than others for heating body shops?

Yes indeed.

That's where you need to do a bit of homework. A thorough review of the various infrared tube heater manufacturers can turn up some surprising differences between brands and product offerings. In your search, ask about burner design (are controls isolated from the air stream? They should be.), emitter tubing (heat-treated aluminized or cheaper hot-rolled steel?), reflector efficiency (50% efficient or 100%), and warranty (10 years is better than 5 years).


Brake Check in New Jersey

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in New Jersey. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in New Jersey. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

Auto Body Shops - Few Tips For Dealing With Them

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in New Jersey is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

What to Look for in an Auto Body Shop

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in New Jersey are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Buy Used Tires

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in New Jersey is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

Wheel Alignment and Tire Balancing: Why Are They Important?

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

Ever since mankind realized they could harness the power of horses and use this as a means of transportation there have been accidents.  Today we associate horsepower with motor engines and where once we had just a single, pair or team of horses providing the energy to move the vehicle, we now have the power of many hundreds of horses under the bonnet of the modern motor vehicle.  With this increase in power comes an inevitable increase in accidents and accidents invariably include dents.

One of the biggest issues facing someone who has been in a motor vehicle accident is the question of where and how to get their vehicle repaired.

Collision services are a collective body of services that assist motor vehicle owners in getting their vehicles back on the road after a collision.  It includes the after crash repairs offered by auto repair services such as repairs to the body of the vehicle ie dent and frame repairs and paint work.  Some auto repair shops work directly with insurance companies thereby reducing the need for the car owner to have to make too many decisions during what is often a very stressful time.

As with all these types of services, finding a quality, reputable company with qualified and experienced technicians to do the work is of paramount importance.  Dodgy work done by dodgy repair shops will not only end up costing you far more down the track when you inevitably have to get their repair work repaired, it may also be potentially dangerous.

Top Tips For Finding A Good Collision Service

Right at the top of the list is ‘ask a friend’.  Word of mouth and personal referrals have long been acknowledged as one of the most valuable, if not THE most valuable, forms of marketing in existence and there’s good reason for that.  It’s the one more people trust more than any other form of marketing.  So if you know someone who has been involved in a car accident and is happy with the repairs that were done on their vehicle and the customer service they received, ask them where they had the work done.  You can also ask local businesses in the auto trade if they have any particular recommendations or know of any reasons why you should maybe avoid certain repair shops.

Tip number 2 is to take matters into your own hands and conduct some one on one research.  Approach your local auto repairers and talk to them about the service they can offer and the guarantees they provide on their work.  Ask if they have photos of some of the work they’ve done that is similar to what you require and, most importantly, whether they have unsolicited customer feedback you can view.

And tip number 3 is that Google is often your best friend when it comes to research like this.  Look up local repair shops online, check their websites for photos and videos of their work and their customer feedback.  See if they have customer reviews on some of the big review sites like Yelp or, if they have social media pages ie Facebook, Google + etc, whether customers have left feedback there.

What You Need To Consider When Searching For An Auto Repairer

Not all makes of vehicles are created equal and not all auto repair shops can repair all makes of vehicles.  Therefore ruling out any who don’t deal with your make will narrow your search.

Which ones provide a warranty on their work, and how long is the warranty.  A warranty not only provides you with peace of mind, it’s also a good way of telling whether or not a repair shop has faith in their workmanship.  As a general rule, the longer the warranty period the more faith the repairer likely has in their work.  If you can find one that offers a lifetime warranty so much the better.

How are you going to get your vehicle to the repair shop if it’s too badly damaged to get there under its own steam?  If this is the case, you may want to find one that either has a towing service or can arrange for a towing service to get the vehicle to them.  Unless you have motor insurance or a motor club membership that includes towing.

How long can you function without a vehicle?  If you don’t have alternative transport and you rely heavily on your vehicle then you’ll need to find out how long each repairer estimates it will take them to fix it.  However, don’t sacrifice quality of workmanship for speed because chances are you’ll end up spending more time without a vehicle down the track when you have to take it back to have those hastily done repairs repaired.

And last but not least, getting back to word of mouth and doing business by personal recommendation.  Make a point of checking feedback provided by previous customers.

 

Bike Brake Overview

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In New Jersey Should Help You With What Car Needs Exactly?

Brake Job

Students who graduate from Surry CommunityCollege’s Collision Repair and Refinishing Technology program can pursue careers as painttechnicians, body technicians, service writers, insurance adjusters, insurance estimators,auto detail technicians, and retail sales associates.

Autobody classes are also offered to peoplewho would like to simply learn how to fix up their own vehicles as a hobby.

Night classes are offered.

Hello, my name is Jeff Boles, and I am theLead Instructor for Collision Repair and Refinishing Technology here at Surry Community Collegebetter known as the the Autobody program.

We offer classes in painting and refinishing,nonstructural damage, structural damage, automotive MIG welding along with a plastics and adhesivesclasses.

We also offer courses on special finishes,automotive detailing and autobody estimating.

Diploma seeking students can choose to takea Work-Based Learning option where they can work for a company while also earning a classcredit.

The Autobody students are working on a 1932Ford Roadster Project Car, which will be displayed at college and community events.

Students also bring their projects from homeand can take the classes over in order to use the college equipment and facilities.

Students like the flexibility of our program.

We have students studying for a certificateand diploma, while some students are just taking the course for enrichment and to beable to repair their own vehicle.

Students can earn a diploma or certificatein Collision Repair and Refinishing Technology and be ready for full-time employment in theAutobody industry or simply take Autobody classes for a hobby.

I am a student at the Surry Early College,and I am taking the Automotive and Autobody classes.

I am really enjoying the Autobody classes.

I get to work on my own projects.

They help me out.

I am getting college credit and high schoolcredit.

It’s also tuition paid.

I don’t have to pay anything to take it.

It’s really great for me.

After I graduate, I am hoping to go into ashop.

I am wanting to work for somebody for a while,and then after I get experience of how to run my own business and do my own thing, thenI want to open up my own shop.

Well, behind me is a 92 Ford Ranger.

I had it as my first vehicle.

I wrecked it.

When I wrecked it, I had a plan.

My plan and my vision is to put Cummings turbodiesel in it.

Right now I am fitting it to a 78 F-100 chassisand suspension.

It’s got a Dana 44 straight front axle underit and a 9-inch rear, so that was already done.

I don’t have to do the swaps or anythinglike that.

I am just going to do a little bit of bodywork, put the Cummings in it and hopefully, it’s done.

The work I do is very satisfying.

I love working with my hands, and I love workingwith cars and seeing how they turn out.

The instructors are very helpful.

When I have a question, they are right thereto answer it.

If I need something, some kind of guidance,they show me and then they let me do it.

One of the reasons I chose to take Autobodyhere at Surry was that I have always wanted to paint cars give those custom paint jobs.

That's one of the reasons I took it.

This right here is my truck that I have beenworking on restoring it.

I want to give it an aftermarket paint jobsomething that would look nice.

The instructors here are helpful and knowledgeableon anything they need.

They know their thing so whenever you needhelp or when you are doing something they will come and help you out.

You get it done the right way.

This is really exciting.

You are always excited when you start somethingto get it done.

I grew up as a tomboy working on a farm helpingmy paw.

That’s probably what got me into likingand working on cars.

I love cars.

I like working in Autobody because I likeworking with my hands and working on cars and helping people.

I am just going around helping people likeNancy over here.

I help her a lot.

The other day I helped her take an exhaustoff.

I helped David sand his truck a little bit,and I been working on the school’s hotrod.

I painted the bottom of it.

I was just going to take automotive, but nowI have decided to take Autobody because most of these dealerships are going to have Autobodyand Automotive so that’s a double whammy.

When I get out of college, graduate, I’dlike to work at a dealership.

I hope to get a job at a Jeep dealership becauseI love Jeeps.

Autobody professionals make about $39,000per year or more based on experience.

Extremely successful Autobody shop ownerscan make in the neighborhood $60,000 to $100,000 in the Piedmont Triad area.

High school juniors and seniors can take Autobodyclasses tuition-free through the Career & College Promise dual enrollment program.

For more information, go to www.

Surry.

Edu.

You can also follow the program on Facebook@SurryAutobody.

Prevent Common Problems with Body Filler


Best Auto Body Shop in New Jersey