Best Auto Body Shop in New Jersey

If you’re looking for an auto body shop in New Jersey make sure you give Peotters Tire & Auto a call as the New Jersey areas premier tire and brake shop. Today’s vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop in New Jersey to be aware of the different materials and techniques used for repairing them.

Auto body shops like Peotter’s Tire and Auto and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills.

A good, eco-friendly auto body shop in New Jersey will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

Jeff what are the three questions should ask a body shop before they consider dropping their car off for repairs? Well what's important is that the repair shop actually be qualified to fix that particular vehicle.

Today modern cars require specialized training and equipment to be able to perform repairs to the manufacturer's standards.

For instance, this Mini Cooper and other BMWs require what's called rivet bonding.

So, glue joints and rivets.

They're actually repaired like aircraft today.

This is important because this maintains the structural integrity the manufacturer designed for a repair situation.

Like this fixture frame bench here that utilizes actual jigs to support the vehicle across its entire platform and place factory components precisely where the manufacturer has designated.

These systems are different than generic systems that simply are reverse engineered and don't have jig and holding capacity.

Shops that aren't trained and equipped to properly perform a repair utilizing generic equipment or generic procedures can't restore the vehicle to the manufacturer's standards and that doesn't necessarily maintain the safety ratingdesigned for the vehicle.

You potentially jeopardize the collision energy management system.

The vehicle might not perform the same in a future collision and you could possibly be more injured than you would if the car doesn't perform as the manufacturer intended.

The second question a consumer should ask is "Where does the body shop's loyalty lie?" Is it an independent repair center that relies on satisfied customers to drive business through their door and therefore fixes vehicles correctly? Or is the body shop on the insurance company's "preferred network?" Those body shops rely on the insurance referrals and when those body shops utilize cheap, imitation, and savage parts utilize the quickest possible repair times and keep costs as low as possible that generates the next referral.

But that's a recipe for shortcuts.

The third question, Paul, is "Can the repair shop make this process convenient for me?" Most consumers today want convenience and ease.

Repair shops that are high-quality repair shops are going to put their customers' interests first & do everything they can to have a satisfied customer.

That includes sheduling a rental car, scheduling a tow engaging in conversations with the insurance company and making sure the vehicle is fixed right for the consumer.

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part.

Tire Repair Places Near Me

Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.

Who Really IS the Best Auto Body Shop in New Jersey ?

Car Battery Replacement Near Me

Before you try to run out and find auto body shops near you, take a moment to read through this article and consider including some of my personal experience as a mechanic into your own personal deliberation about what constitutes the best auto body shops in business. When you break things down, there are really two types of garages in business: good ones and bad ones. The best place to start when trying to scope out a potential body shop is the owner. In bad auto body garages the owner usually instructs the employees to give the impression that your car is in worse shape then you think, or that something is broken and needs to be fixed right away. In a legitimate auto body garage, the owner is more concerned with forging a long standing relationship with you and getting your repeat business rather then just ripping you off and potentially never seeing you again.The reason why most owners are concerned with ripping people off, especially in a body shop, is because the only two reasons cars ever go in there is for repairs on collision damage or for custom work; this means that the owners of the shop realistically do not see the owners of vehicles too often and do not see the value in repeat business, they would rather try to squeeze every dime out of your while you are there.The best auto and body shop you can ever find is where the owner looks to develop long term relationships with their clients. While it is true they can potentially never see a newer customer again, these owners are smart and do the best work possible not only to help you out, but to impress you and have you refer your friends and family to him or her. These owners are less interesting in gouging your wallet and more interested in establishing a reputation in their local community for outstanding work and service. These types of people see the value in what it means to be a true professional and are more successful then their more selfish friends in the business.The best way you figure out which owners are the good or bad guys is either by your own direct experience or the experience of others. You should not be afraid to talk to the auto body shop manager directly and begin to get a feeling for what he is about. After a short conversation and carefully studying his body movement and language, the first impression you get is often the right one.

Secrets of the Auto Body Shop

Tire Company Near Me

What Is Caster - Camber - Tow-in - Wheel AlignmentFirst for those who do not understand caster, camber, and tow-in let me explain. Caster is how the wheel is in relation to a vertical king pin or ball joints. It can be true vertical or -o- degree, positive, or negative. Example: the front wheel of a bicycle has positive caster. Note the wheel extends forward from the turning axis. Therefore allowing the steering to return straight when you remove your hands from the handle bars. A vehicle with positive caster will do the same. This adjustment is for handling or how it drives and requires caster - camber gauge for adjustment as well as certain hand wrenches.Camber denotes the position of the wheel to the vehicle, such as in at the top and out at the bottom (negative), or out at top and in at the bottom (positive). The recommended setting can be negative 1 to positive 1, -0-degree being straight up and down, or true vertical. If it is extreme one way or the other it will cause wear on the inter or outer edge of the tire and possible scallops may appear. This adjustment is for tire wear and possibly some handling, also certain tools such as upper control arm wrench and a tomcat camber adjustment tool may come in handy.There are times when one shim or adjustment to move the rear of the control arm outward will give a wheel the proper setting if one understands what that move will do for both settings (caster and camber) simultaneously. That knowledge or understanding plus the proper hand tools and some experience is all that is really needed. Well, maybe a good coach would come in handy. However, back to the move made by the adding a single shim to the rear of the upper control arm (by the way shims vary in thickness) would give less negative caster and more positive camber. I hope this helps! Any questions? Lem Boydhttp://www.uniquetoolsaccessories.com


Brake Check in New Jersey

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in New Jersey. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in New Jersey. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

Body shops say insurance companies are skimping on repairs

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in New Jersey is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

What Happens If You Wreck a Leased Car?

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in New Jersey are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Autobody Shop

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in New Jersey is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

Mountain Bike Travel: Things You Should Never Forget

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

What Is Caster - Camber - Tow-in - Wheel AlignmentFirst for those who do not understand caster, camber, and tow-in let me explain. Caster is how the wheel is in relation to a vertical king pin or ball joints. It can be true vertical or -o- degree, positive, or negative. Example: the front wheel of a bicycle has positive caster. Note the wheel extends forward from the turning axis. Therefore allowing the steering to return straight when you remove your hands from the handle bars. A vehicle with positive caster will do the same. This adjustment is for handling or how it drives and requires caster - camber gauge for adjustment as well as certain hand wrenches.Camber denotes the position of the wheel to the vehicle, such as in at the top and out at the bottom (negative), or out at top and in at the bottom (positive). The recommended setting can be negative 1 to positive 1, -0-degree being straight up and down, or true vertical. If it is extreme one way or the other it will cause wear on the inter or outer edge of the tire and possible scallops may appear. This adjustment is for tire wear and possibly some handling, also certain tools such as upper control arm wrench and a tomcat camber adjustment tool may come in handy.There are times when one shim or adjustment to move the rear of the control arm outward will give a wheel the proper setting if one understands what that move will do for both settings (caster and camber) simultaneously. That knowledge or understanding plus the proper hand tools and some experience is all that is really needed. Well, maybe a good coach would come in handy. However, back to the move made by the adding a single shim to the rear of the upper control arm (by the way shims vary in thickness) would give less negative caster and more positive camber. I hope this helps! Any questions? Lem Boydhttp://www.uniquetoolsaccessories.com

Wheel Alignment and Tire Balancing: Why Are They Important?

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In New Jersey Should Help You With What Car Needs Exactly?

Goodyear Tire Deals

For the majority of drivers, going to an auto body shop is a mysterious experience, a scary encounter with the unknown. Once you hand over your key, you instantly feel uneasy; will your car be returned as good as new, or will the repair specialists do a shoddy job? How will you know? How will you be able to figure out if you hard-earned money is just being tossed down the drain?

The best way to know if you are receiving excellent service and professional care is to find a reputable body shop and then build a relationship with that shop. However, most people who take their vehicles in to the shop are doing so for the first time. So, how do you know whether or not you can trust an auto body shop?

First of all, it is important to know that most auto body shops are reputable businesses. The majority of auto shop owners are just struggling to make a living like most small business owners - they want to do a great job on your car so you will return or refer others to their shop. However, there are a few bad apples that spoil the whole bunch, and you need to be diligent when selecting a shop.

The first thing to do is get a referral or locate a shop online using reviews and testimonials. Create a list and call each shop to see how well you are treated on the phone. Select three or four shops that sound good and are in close proximity to your location, and you are ready to take your vehicle in for an estimate.

You should get at least three estimates from three different shops. The estimate may vary because shops may use different estimating software, but they should all be in the same ballpark. If an estimate differs by a great deal, you should ask why. The body shop expert should be able to explain all prices on the estimate, including all price quotes and labor charges.

When you get the estimate, you should also be evaluating the customer service. How quickly were you acknowledged? How efficiently were you helped? Were all members of the staff polite and friendly? Did the staff seem knowledgeable? Be observant during the estimate and you will have a good idea of how you will be treated during the entire repair process. If the customer service seems lacking, move on to the next place even if the estimate seems reasonable.

If you decide to leave your car, and the shop contacts you later to tell you about additional charges, this may be a sign that it is not a reputable and honest repair facility. Though additional charges can happen occasionally, it is not a common practice for a reputable shop.

If you do your homework, have some patience, and get a few estimate, the odds are good that you will find a reputable auto body shop. Once you have found one, it helps to direct all your business to them, and refer them to others. If you do this, you will have established a good relationship, and you will no longer need to worry about finding an honest auto body shop.

Wheel Alignment and Tire Balancing: Why Are They Important?


Best Auto Body Shop in New Jersey