It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in Madison. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.
What is the next step after your collision and you need an auto body shop?
Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.
Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in Madison.
They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.
This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.
Auto body (Collision Repair and Refinishing)
Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.
Now here are some things to watch out for. a local auto body shop in Madison is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.
Laser Wheel Alignment: Chassis Mounted Vs Wheel Mounted
Replacement Parts in Auto Body Shops
Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in Madison are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.
Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.
No Realignment? Talk to Your Auto Repair Team!
The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.
Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.
Using Bondo (Fillers) Instead of Replacing the Part
Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in Madison is doing, they tell you, and this is what you are paying for then it is fine.
The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.
Wheel Alignment Tech Talk - Camber, Caster, Toe-in
All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!
Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.
The nation's top mechanics are rejecting the recommendation by some in the auto field that cars can go 5,000 miles or more before oil is changed. National Institute for Auto-motive Service Excellence (ASE)-certified Master Automobile technicians weighed in on this and other issues in a survey conducted by Valvoline. The survey covered the controversial recommendation and trend toward longer intervals between oil changes, as well as the costs to car owners of delayed maintenance. "Certified Master Automobile Technicians are the best of the best," said ASE President Ron Weiner. "They are on the front lines of taking care of today's vehicles and they have definite thoughts on how motorists can participate in making their cars and trucks run better and last longer." Oil Change Frequency Mechanics view oil as the lifeblood of the car engine, with 84 percent saying not getting a regular oil change can cause the most problems for a vehicle, when compared to other maintenance issues. Sixty percent said the oil should be changed at 3,000 miles-the longtime, recommended standard. According to the survey, Valvoline remains the number one choice of ASE Master Automobile Technicians for use in their own cars and trucks, and is the brand of motor oil most recommended by them to customers, friends and relatives. "Changing oil with quality motor oil, like Valvoline, at regular intervals is the best way to prevent damage to your car's engine and keep more money in your pocket," said Valvoline Marketing Director Bryan Emrich. He added that regular oil changes protect the engine and reduce sludge, which can impact engine perfor-mance and cause costly repairs. Delayed Car Maintenance While car owners know, intellectually and intuitively, that regular maintenance is important to keeping their four-wheeled investment in safe condition and working order, the reality is that more and more Americans are not listening to conventional and proven wisdom. The vast majority of mechanics-87 percent-said they believe American car owners are putting off routine maintenance, mostly for cost reasons. Ironically, they overwhelmingly said-at 97 percent-that delayed care will cost an owner much more in the long run, as problems left unattended can multiply and lead to other issues.
What Is An Damage Repair Estimate? - Auto Estimating Part 1
The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.
Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.
Your Auto Body Shop In Madison Should Help You With What Car Needs Exactly?
>> I'm Chad.
I'm a second-year student here at DCTC.
I've been an apprentice at ABRA inBloomington for just about a year, now.
Doing some frame damage,here, repair on a 2005 Ford.
Three door, got hit here,and this here was the main impact.
We've already cut the reinforcementand impact bar off.
Now, we're going to be pulling onthis frame here, to get it straight, using the three-dimensionalmeasurement system to make sure that everything else is inline where it should be.
>> I'm Gerry Rainford.
I'm a second-year instructor here,at Dakota County Technical College.
Chad's a typical second-year student, wherewe get into different levels of repair needs, from just simple door repair to, well, you cansee here, is a full unibody reconstruction.
Mechanical aspects, as well.
Getting into the air conditioning andother mechanical systems on the vehicle.
This is kind of the way that once we havethe vehicle anchored on our frame rack.
We come through and we can actually do pull out.
We're going to be doing a light pull,this morning on the unibody structure.
We're going to see if we can't repair the rails.
Typically, when they're kinked to thispoint, we would do a replacement procedure.
But we're going to see ifwe can't repair them, today.
So, we'll just kind of talk as we go through it.
And we'll see if we can getthe rails to come out.
So, Chad, please take over from here.
>> All right.
I'm going to be using these towers, here, thatare capable of pulling 10,000 pounds apiece.
Try to get this mash come outon this left frame rail, here.
>> So, once again.
We're going to be pulling at a constantlevel that's going to be straight out, to try to replace the height, thelength, and width of the rail.
So, we're going to keep the directionstraight and at a straight pulling distance.
>> And all I'm doing here, now, is justwatching as I'm pulling, going slowly to find out how the metal's going to react.
Everything reacts different,not any accident is the same.
Everything needs to be takenon with a different viewpoint.
What I'm going to do now, isjust hit this metal, here, to try to relieve some of this stress.
[ Hammering Sound ] And always while you're pulling,what you're going to want to do is check your anchoring points, again, tomake sure that the car is not going anywhere.
Make sure all your chainsand clamps are still tight.
As you'll notice, I'm staying above,not standing behind these chains, just in case anything would happen to let go.
[ Hammering Sound ] >> Let's work the backside of the railthrough here a little bit, as well.
[ Hammering Sound ] [inaudible] target.
One of the things we don't want to do, is we don't want to do additionaldamage as we're pulling.
Looks like we're pulling morefrom the bottom of the rail.
>> Than we are from the top.
So, at this point in time, I think we shouldstop, rehook, and grab a hold of the top of the clamp support and pullmore on the top of this rail.
>> All right.
Both these dozers here are run by the same pump.
So, as I pull it's going to pull them equally.
Let's get some pressure on there.
[ Inaudible Comments ] [ Hammering Sound ] >> Just trying to relieve this stress.
Move the metal where I want it.
>> So, let's get a couple ofhits with this on the backside.
[ Hammering Sound ] Right now, we're concernedwith overpulling on it.
And so, I think we're going to stop.
And we're going to regrab ontothe rail at a different location.
Once you've overpulled and it distortsthe rail, then we've got an issue.
>> We're going to cut this outsideof this rail, here off, this cap.
Just a piece of the sheet seal,here, out of high strength steel.
We're going to pull this out here, sothat way we can get inside here, too, and make proper welds and getthis metal straight, again.
I'm just going to be countered along,drill out these spot welds, here.
And then, cut it here at the seam.
I'll run a line, section it out.
>> Why don't you show them how we know how farwe need to pull by using the measuring system? Then, to explain the measuringsystem, real quick? >> All right.
As we pull out on this stuff here, toget this rail out to where it should be, these targets here measure with this beamunderneath the vehicle, measures the vehicle at all kinds of different points.
Four in the middle of the vehicle, twoat the rear of the vehicle, and then, these here in the front closest to the damage.
This vehicle, this chart here for thevehicle is specific for this vehicle.
What this does here, is it hangs targets fromthe vehicle at specific manufacturing locations.
It measures the vehicle throughout there.
You can tell that our centersection here, is good.
And the back of the vehicle is good.
But up here, we're dealing with offmeasurements on the front end from the impact.
>> We're going to take and when we getthe rails pulled back into a location by the manufacturer's specifications, we'lltake, we'll hammer and dolly all this straight.
And we'll take, we've got new components.
We've got a new reinforcement barthat we'll be welding into place, to replace the structure of the vehicle.
But we'll come through, replace the.
You want to come around over here.
You can see that the radiator condenserhas been damaged in this accident.
And it's completely, we've lost all the Freon.
So, we'll be doing an R and Rprocedure on the condenser assembly.
Then, we're going to evac andrecharge the air conditioning system.
And then, move forward with the restof the mechanical repairs at this time.
In some situations, when you getcomposite intake manifolds, like this, components can come back and dodamage to the intake manifolds, starters, alternators, AC compressors.
We have additional damage deeper in the vehicle.
And this one, we've simplygot a condenser to replace.
What's so, how long will ittake you to do this repair? >> This repair here, will take me probablyabout two weeks to finish, to complete.
Done quite a bit already.
Already had all my parts ordered.
Those have already been checkedin and identified, and made sure that they are the rightparts, so I'm not scrambling at the end of the project to find the correct parts.
I'd say about two weeks; two to three weekswould be a good timeline for this vehicle.
>> Well, thank you, Chad.
I appreciate it, taking your time withthe students and this is what we do here at Dakota County Technical College.
It's a two-year program.
We try to get you ready with the latesttechnology and the latest equipment to make sure that they're ready for the industry.
And so, they can be productive and profitablein today's unibody reconstruction world.
Thanks, very much.