Tire Repair in Madison

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in Madison. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in Madison. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

How to Pick the Right Auto Body Repair Shops

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in Madison is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

Mechanics Veto Extending Oil Changes

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in Madison are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Collision Shops Near Me

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in Madison is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

What Are Collision Services? How Do They Work?

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

What is a wheel alignment? How does it effect handling and tire wear? When should I do an alignment? What causes alignments to go out? How would I know if my alignment is out?  A wheel alignment is nothing more than setting the angle of the hub/wheel so it tracks in the right direction. Most vehicles have four-wheel alignments, meaning each of the four wheels is separately aligned.  Your basic alignment consists of three angles: camber, caster  and toe-in. Camber is the tilt of the tire when viewed from the front of the car. Positive camber means the top of the tire is tilted away from the car. Negative camber means the top is tilted in. Camber has a lot to do with cornering performance. Too much negative camber will wear the inside of the tires prematurely. Too much positive camber will wear the outside tread. Caster is the inclination of the front spindle. Picture the angle of the forks on a bike top to bottom. When the caster is out, it creates a pull or wandering condition and sometimes a slow responding steering wheel. Toe-in is measured in inches or degrees. Viewing from the front of the car, it is the difference between the front and rear center-line of the tire. Toe-in means the fronts of the tires are closer together. Toe-out means, the fronts of the tires are farther apart. Toe-in or out has the most effect on tire wear. There is a lot more to suspension alignment, especially if you push your vehicle on the track. The modifications you make on your suspension are just the beginning. Once you start down this road you will be concerned with things like bump steer, weighting (vertical load), preloading, tire traction versus tire load, and more. Now you're thinking under-steer, over-steer, tire compound, sway bar design, and other topics that can be covered in a later article. For now, just remember to have your vehicle aligned every 10,000 to 12,000 miles in normal driving conditions.If you accidentally hit a curb, or drive through a nasty pothole or other road obstruction, that would be a cue to have your car's alignment checked more often. Proper alignment is good for your car. It will save unnecessary wear on your tires. It will ensure that your vehicle is giving you the handling the factory designed the car to have. And, most importantly, a properly aligned car is safer and more fun to drive.   

What Are Collision Services? How Do They Work?

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In Madison Should Help You With What Car Needs Exactly?

Used Wheels

What Is Caster - Camber - Tow-in - Wheel AlignmentFirst for those who do not understand caster, camber, and tow-in let me explain. Caster is how the wheel is in relation to a vertical king pin or ball joints. It can be true vertical or -o- degree, positive, or negative. Example: the front wheel of a bicycle has positive caster. Note the wheel extends forward from the turning axis. Therefore allowing the steering to return straight when you remove your hands from the handle bars. A vehicle with positive caster will do the same. This adjustment is for handling or how it drives and requires caster - camber gauge for adjustment as well as certain hand wrenches.Camber denotes the position of the wheel to the vehicle, such as in at the top and out at the bottom (negative), or out at top and in at the bottom (positive). The recommended setting can be negative 1 to positive 1, -0-degree being straight up and down, or true vertical. If it is extreme one way or the other it will cause wear on the inter or outer edge of the tire and possible scallops may appear. This adjustment is for tire wear and possibly some handling, also certain tools such as upper control arm wrench and a tomcat camber adjustment tool may come in handy.There are times when one shim or adjustment to move the rear of the control arm outward will give a wheel the proper setting if one understands what that move will do for both settings (caster and camber) simultaneously. That knowledge or understanding plus the proper hand tools and some experience is all that is really needed. Well, maybe a good coach would come in handy. However, back to the move made by the adding a single shim to the rear of the upper control arm (by the way shims vary in thickness) would give less negative caster and more positive camber. I hope this helps! Any questions? Lem Boydhttp://www.uniquetoolsaccessories.com

Auto Body Shops and Custom Work


Best Auto Body Shop in New Jersey