Best Auto Body Shop in New Jersey

If you’re looking for an auto body shop in New Jersey make sure you give Peotters Tire & Auto a call as the New Jersey areas premier tire and brake shop. Today’s vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop in New Jersey to be aware of the different materials and techniques used for repairing them.

Auto body shops like Peotter’s Tire and Auto and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills.

A good, eco-friendly auto body shop in New Jersey will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

One of the most important parts of your bike is the braking system. Without working brakes you would soon get into big trouble. Keeping your brakes in best shape is important. Fortunately, it is also relatively easy. Here is short bike brake overview.

Nowadays, you have three popular types of brake systems:
– Rim Brakes
– Disk Brakes
– Hub, or Drum, Brakes (including the Coaster Brake)

A number of other types of brakes have been used and are still used but they are not as popular as the three types mentioned above. Note that some recumbent bikes have no brakes. Obviously, don’t use such bikes in traffic. You may have noticed that track bikes are fixed-gear bicycles without any brakes. Actually, they don’t even have freewheel. But they are only used at a velodrome.

The old foot brake is not as popular as it used to be. It is also known as coaster brake and belongs to the drum brake category. The first coaster brake was invented back in 1898. The foot brake has one important advantage, since it is internal it works fine in all weather conditions. Foot brakes work for years without any maintenance but if it breaks, repairing it is generally very complicated. Since coaster brakes can only be applied to rear wheels, skidding is always a possibility. Another problem is that the brake can overheat if used too much. A practical problem is that the pedals need to fairly level, otherwise it will be difficult to brake. But combination of a hand-operated front wheel brake and a foot brake is efficient.

Mountain recumbent bikes generally use disk brakes. The system is simple, a metal disc is attached to the wheel hub. When the brake is applied, the pads squeeze against the disc. There are two types of disk brakes, mechanical and hydraulic. Disk brakes have many advantages but they are generally more expensive and heavier than other brake types. They tend to perform well in all weather conditions. They don’t overheat like rim and hub brakes when heavily used. Unlike rim brakes, they don’t heat up the rim and cause the tire pressure to increase.

Rim brakes are cheap, light-weight and relatively easy to maintain. The principle is very simple, two brake pads, typically made of rubber, squeeze the rim and slow down the cycle. You have a number of different models of rim brakes. The most common are Cantilever, V and center-mount brakes. Their main disadvantage is that they work badly in wet conditions. In muddy conditions, clogging can be a problem. They can also overheat the rim, which increases the air pressure in the tire. This could in worse case cause the wheel to explode.

Obviously, your budget will determine which stationary bikes are worth having a closer look at. Often the difference between the bikes is small, despite that the price difference is large. Although exercise bikes are fairly simply devices, some of them can get noisy after a couple of months. It pays off reading reviews from buyers of the stationary bikes you are interested in. For most people, the number of workouts you get with the bike is not especially important. Nowadays, almost all exercise bikes include the very few basic workouts you really need. More important is that the bike is sturdy, a flimsy bike is very annoying to use. Almost all of the exercise bikes from the well-known manufacturers are of good quality. But if you are thinking of buying a cheap exercise bike from an unknown manufacturer, make sure to test it thoroughly before buying it.

Note that especially recumbent exercise bikes are large and heavy, so it can be both difficult and expensive to return them. Thus, the cheapest bike may not the best exercise bike to buy.

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part.

Tire Finder

Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.

Who Really IS the Best Auto Body Shop in New Jersey ?

Automotive Air Conditioning Repair

It happens to all of us at one point in time. We get into an automobile collision. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.What is the next step? Likely, after informing the insurance company you take your vehicle to one of their "approved" vendors.Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.This statement is given to the body shop. It comes with a break down of what the labor and parts "should" be and the company has to usually be able to totally fix the car for that price. Keep in mind that what is printed out represents the best case scenario and doesn't allow for items on the car that was missed or problems that come up.Now here are some things to watch out for. Local body shops are operating under very, very thin margins and the incentive to "cut corners" is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.Replacement PartsMake sure the parts being used on your car are OEM parts. These are replacement auto body parts are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with. Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.No RealignmentThe frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely.Using Bondo (Fillers) Instead of Replacing the PartFilling any damage in with bondo is not bad in itself. If you know what they are doing, they tell you, and this is what you are paying for then it is fine. The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle. All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before).Keep in mind that most auto body repair shops are honest and are surviving in a tough industry. The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. Nevertheless, corners should not be cut at your expense and being watchful is just a smart way to go.

How to Spot a Scam Auto Body Shop

Paint And Body Shop

(upbeat music) - Hey, this is Donnie Smith.

Have you ever overground metal, making it too weak and too thin? Well it's not that hard to do with these thinner metals.

What about when working with body filler? Have you ever gotten it in cracks, gaps, other placesthat you don't want it? Takes quite a bit of time to get that out of there and clean it up.

So if you'd like to learn some tricks, how to prevent over-thinning your metal when working with thin metal, and how to keep fromgetting all the body filler in the places you don'twant it in the first place, then you're in luck, because that's what we'regonna show you in this video.

Alright, let's just goahead and get started.

What we're gonna do to eliminate grinding a lot of the metal off,is to use a DA Sander, and we can use 36 grit, or 80.

I'm using 80 here.

That usually works well.

May take just a little bit longer to remove the paint coatings, but you're not gonna chancegrinding too much metal off.

This does not take the amountof metal that grinding does.

Now with thinner metals,I would recommend this.

Now if you're working on older vehicles, grinding may be a little quicker, and that may still work fine.

Okay, now for the tip of how to eliminate getting body filler in places you don't want it, and that's simply to mask it off.

On the edge, I don't want the body filler wrapping around the edgewhere I have to clean it up, so I'm gonna mask that off.

Any gaps, for instance here, there's a, where the molding goes, I don't want body filler to wrap in there where I'm gonna have to sand it out, so I'm gonna use the bodylines that's on the car, and use that as a dividing line to make nice, sharp lines at, so that the body fillerdoes not get in these areas.

(upbeat music) Okay, now I'm mixing thebody filler up in the tube.

I'm gonna let the air out of the cap, so that it'll mix well.

And once I remove some of the air, I'll put the cap back on, and now I'm just gonnamix it inside the tube, because this hardener reallydoes separate a lot in there.

If you don't do this, you'll have liquid-ysubstance that comes out, and you don't want that, so be sure that you mixit up well in the tube before you use it.

Now I've already got somebody filler out here, and I used a paint stick toput some on this mixing board.

And I'm gonna get this hardener, I'm gonna apply a stripfrom edge of the body filler to the other, and that usually is a pretty good mixing ratio.

And notice I'm using a spreader to mix it.

I'm not using a paint stick to stir it, because that could put air bubbles in it.

If you get air bubblesin your body filler, that's gonna create pinholes, whenever you go to sanding body filler.

So it's always best towork the air bubbles out.

Just spread it out on your filler until it's nice and uniform.

You don't want there tobe any hardener streaks.

You wanna mix it until it's one color.

(upbeat music) Okay, now I have the filler mixed good.

It's nice, uniform, one color.

We don't have any hardener streaks in it, so we know that it's mixed well.

I'm gonna apply the body filler.

Now to do this, I'm gonnaapply a tight coat first, and what that is, iswhere I take a thin coat of body filler, and push really hard down on the spreader, so thatI push it into the metal.

That helps it adhere better to the metal, so that you don't have any problems with adhesion at a later point.

Now once I get the tight coat on, I come back with a fill coat, and that's where I'm gonnaput a little bit less pressure on the spreader, which allows it to fill the damaged area in.

(upbeat music) Okay I have the fill coat applied.

Now here's a tip for you to eliminate a lot of the sanding, and that is to work on your edges, because if you have real hard edges, it's gonna take more sanding.

So what I'm doing here, is I'm using the spreader, and on the edges I'm kind of feathering that body filler out, so that edge is a real thin layer, and you don't have that big, hard edge to try to sand out.

Okay, now let this setup for just a little bit, and you don't want to do it immediately after you apply the body filler.

You wanna let the filler set, but you don't want it to be dry either.

But as it's kind of in its green state, go ahead and pull the tape off.

This will leave you nice clean edges.

And also before it fully cures, you can block sand lightly, you don't wanna sand too hard, just to help level someof the highs and lows.

Okay, now I allow it to dry, and started block sanding it.

Now I'm starting out with 36 grit, because that's gonna levelthe filler really fast, but notice that I'mstaying within the filler.

My block is not slidingout onto the paint, because I don't want those deep scratches getting onto the paint surface.

I'm just wanting to level the filler.

(upbeat music) Also notice that I'm sandingin different directions.

I'm not just going at oneangle the entire time.

So I change it up.

And what sanding indifferent directions does, is it's gonna help youget a more level surface.

So always sand in different directions.

(upbeat music) (sanding) (upbeat music) Once you have it level, switch to 80 grit.

That's what I'm doing here.

First, I'm gonna apply some guide coat, and this just to helpidentify highs and lows, and you'll know whenever you get rid of the 36 grit scratches.

Makes it easier to see this way.

Now also notice I am sandingout on the paint a little bit.

I'm not going too far, but you do wanna sand out further than you did with your 36 grit.

You wanna make sure all 36 grit scratches are removed during this step.

(upbeat music) Okay I finished blocking, and I'm feeling for high areas.

And usually if you seemetal spot areas like this, that's gonna indicate that it is high.

And that happens sometimes, and if it does, what you need to do is get your pick hammer, and lightly tap down on those metal areas.

And what this is gonna do, is it's gonna lower that metal.

(upbeat music) And here's another tip for you.

If you're having problemsfilling the bodywork, and determining highs and lows with your hand, with your bare hand, use something like this, a wipe all, or a towel or somethingto put between the panel and your hand.

And this may help you be able to feel the highs andthe lows much better.

Now I'm gonna use the tape, because I'm gonna be applying some putty, so I'm gonna do the same thingI did with the body filler, the edges, and that indention where the body side molding goes.

I'm gonna tape all that off, to keep all the filler out of that.

Now when using putty, it lays out a littlethinner than body filler, so I usually just go halfway, rather than from one edgeof the filler to the other.

So I'm gonna do about halfthe amount of hardener.

(upbeat music) But everything else is basically the same.

Mix it until it's one uniform color.

Don't want any streaks in there.

And the good thing aboutputty is it's thinner, and it's easier to get a nice skim coat, but you do wanna do the tight coat, followed by a fill coat.

And another thing about a putty, is you can go over the entire repair area, from paint edge to paint edge, and that helps any imperfections you had in your sanding flaws, or sanding scratches,or anything like that, it's gonna fill in.

(upbeat music) And after allowing it tosetup for a few minutes, now I'm gonna peel the tape.

(upbeat music) Now when sanding finish putty, I'm not gonna start out with 36 grit.

I'm gonna start out withthe 80 to level it out.

And also I wanna let it fully dry.

I really don't wanna try to sand putty in its green state, so I'llallow it to dry all the way.

Then I'm gonna get 80 on a block, and I'm gonna sand it.

And I'm gonna cross sand it.

Make sure it's good and level.

(upbeat music) Once I have it leveled with 80, I'm gonna use the guide coat, and then I'm gonna comeback with 150 to 180.

I'm using 150 here I believe, but anywhere between 180and 150 will work fine for smoothing out your 80 grit scratches.

And this guide coat, it will help you identify any lows that you may have if there are any, or let you know whenever you got all the 80 grit scratches sanded out.

(upbeat music) And one last thing you wanna do, before you send it offto start priming it, you wanna make sure it fits.

Make sure everything aligns.

Make sure that your body work is right.

So you're gonna have toput it up to the car, and make sure everything works.

(upbeat music) Always, thanks for watching this video.

Be sure and share it with your friends.

Give us a thumbs up, a like, and be sure to subscribe to our channel.

Also be sure to go to CollisionBlast.

Com.

And there we have hours of free autobody and painttraining videos like this one, and a lot of other resources for you.

Thanks again for watching.

Have a safe and productive week, and we'll see you in the next video.

(upbeat music).


Brake Check in New Jersey

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in New Jersey. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in New Jersey. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

Auto Body Shops - Bumper Repair Vs Bumper Replacement

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in New Jersey is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

Wheel Alignment Tech Talk - Camber, Caster, Toe-in

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in New Jersey are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Brake Job

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in New Jersey is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

Auto Body Shops and Custom Work

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

Tire balancing and wheel alignment are some of the most common auto repair services offered by technicians. When you buy new car tires, you may consider performing a wheel alignment. Having an alignment done can save you a lot of costs in the long run.The Importance of Wheel AlignmentHaving a wheel alignment done will help to significantly increase the life of your new tires. During the wheel alignment, the steering and suspension of your vehicle is going to be adjusted in order to ensure that the tires don't wear out overtime. Alignment is also important because it ensures the car handles corners smoothly.Wheel alignment is needed overtime because as you drive, your car's steering and suspension systems are pushed causing the ball & socket joints, bushings and other mechanical links to wear out. This makes the alignment deflect from the factory specifications. If nothing is done to improve the alignment, your car will have poor cornering and handling which also makes the tires wear out.Tire imbalance can occur when the rubber that is used in making it wears off overtime. That is why it is important to check your tires for imbalance every 6 months and ensure they are rebalanced. Tire imbalance can cause severe accidents especially when the car is driven at fast speeds.Tire balancing and wheel alignment can be done together. These services will help you to avoid budgeting for new tires soon. Even though they can be pretty expensive, they'll prevent serious accidents and increase the service life of your car. Just ensure you visit a well known auto repair shop and find a technician who is skilled and equipped to offer these services.Copyright (c) 2014 Crawfordville Auto and Tire

Mountain Bike Travel: Things You Should Never Forget

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In New Jersey Should Help You With What Car Needs Exactly?

22 Tires

What exactly is an auto body shop? That is actually a good question. An auto body shop is a business that specializes in repairing autos that have been damaged in an accident.

This type of shop is different from a car repair shop. The latter shop just repairs mechanical problems. When the damage to your auto has been caused by an accident, a natural disaster, or some other catastrophic event, you will need to visit a shop that will be able to do these repairs without question.

Although the major reason for seeking out the services of an auto body shop is due to a car accident, a car or truck may also need these type of services if it has been neglected for a long time. For example, if a car has sat for a long time without running, there may be damage to the body of the car. In some cases, wildlife may have damaged wires or even parts of the auto body.

It is also possible that parts of the car will have begun to rust and show wear and tear. These issues must be fixed in order for the car to be safe to drive. In other cases, your car may have been dinged, dented, or scratched in a parking lot. If the damage is significant, you may need to take your car to body shop.The services offered by each shop will vary depending upon a variety of factors.

Some shops specialize in repairing a specific make of vehicle, while others will repair any vehicle that has been brought to them. Some shops only work with certain types of insurance companies while others may only take certain warranty programs. Because of this, it is best to call around before you take your vehicle to a particular shop.

In addition, the cost of the work may vary significantly. If you have been in an accident and need to have your car repaired, you may not want to shop around and compare prices. However, you may be able to save thousands of dollars by taking the time to do just that.

A good auto body shop will be able to replace any broken or cracked glass, mend the dents and broken pieces of the car body, and also fix any mechanical damage. Finally, the shop should be able to repaint the car or paint the part that has been mended to match the rest of the vehicle.

An reputable shop should also have staff which are able to submit insurance claims in order to cover the damage. The staff should also understand insurance deductibles and have a working relationship with local insurance agents. If you do not have insurance, or if your insurance does not cover collisions, a good shop should be able to help you with this situation as well.

The important thing to do is to get an itemized quote which details the cost of the repair. Carefully read over this quote before agreeing to any repairs. Remember, you can always go to another shop to get your car fixed.In some cases, a body shop may even have a loaner car. This means that you will still be able to get to work and run errands while your vehicle is being repaired.

Secrets of the Auto Body Shop


Best Auto Body Shop in New Jersey