Best Auto Body Shop in New Jersey

If you’re looking for an auto body shop in New Jersey make sure you give Peotters Tire & Auto a call as the New Jersey areas premier tire and brake shop. Today’s vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop in New Jersey to be aware of the different materials and techniques used for repairing them.

Auto body shops like Peotter’s Tire and Auto and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills.

A good, eco-friendly auto body shop in New Jersey will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

One of the most important parts of your bike is the braking system. Without working brakes you would soon get into big trouble. Keeping your brakes in best shape is important. Fortunately, it is also relatively easy. Here is short bike brake overview. Nowadays, you have three popular types of brake systems: – Rim Brakes – Disk Brakes – Hub, or Drum, Brakes (including the Coaster Brake) A number of other types of brakes have been used and are still used but they are not as popular as the three types mentioned above. Note that some recumbent bikes have no brakes. Obviously, don’t use such bikes in traffic. You may have noticed that track bikes are fixed-gear bicycles without any brakes. Actually, they don’t even have freewheel. But they are only used at a velodrome. The old foot brake is not as popular as it used to be. It is also known as coaster brake and belongs to the drum brake category. The first coaster brake was invented back in 1898. The foot brake has one important advantage, since it is internal it works fine in all weather conditions. Foot brakes work for years without any maintenance but if it breaks, repairing it is generally very complicated. Since coaster brakes can only be applied to rear wheels, skidding is always a possibility. Another problem is that the brake can overheat if used too much. A practical problem is that the pedals need to fairly level, otherwise it will be difficult to brake. But combination of a hand-operated front wheel brake and a foot brake is efficient. Mountain recumbent bikes generally use disk brakes. The system is simple, a metal disc is attached to the wheel hub. When the brake is applied, the pads squeeze against the disc. There are two types of disk brakes, mechanical and hydraulic. Disk brakes have many advantages but they are generally more expensive and heavier than other brake types. They tend to perform well in all weather conditions. They don’t overheat like rim and hub brakes when heavily used. Unlike rim brakes, they don’t heat up the rim and cause the tire pressure to increase. Rim brakes are cheap, light-weight and relatively easy to maintain. The principle is very simple, two brake pads, typically made of rubber, squeeze the rim and slow down the cycle. You have a number of different models of rim brakes. The most common are Cantilever, V and center-mount brakes. Their main disadvantage is that they work badly in wet conditions. In muddy conditions, clogging can be a problem. They can also overheat the rim, which increases the air pressure in the tire. This could in worse case cause the wheel to explode. Obviously, your budget will determine which stationary bikes are worth having a closer look at. Often the difference between the bikes is small, despite that the price difference is large. Although exercise bikes are fairly simply devices, some of them can get noisy after a couple of months. It pays off reading reviews from buyers of the stationary bikes you are interested in. For most people, the number of workouts you get with the bike is not especially important. Nowadays, almost all exercise bikes include the very few basic workouts you really need. More important is that the bike is sturdy, a flimsy bike is very annoying to use. Almost all of the exercise bikes from the well-known manufacturers are of good quality. But if you are thinking of buying a cheap exercise bike from an unknown manufacturer, make sure to test it thoroughly before buying it. Note that especially recumbent exercise bikes are large and heavy, so it can be both difficult and expensive to return them. Thus, the cheapest bike may not the best exercise bike to buy.

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part.

Brake Change

Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.

Who Really IS the Best Auto Body Shop in New Jersey ?

Frame Straightening

A car is a very complex piece of machinery. Each individual part is vigorously tested before it ever goes into production models and, like a chain, relies upon every other part in order for the vehicle to function. One poorly built aspect can cause serious malfunctions leading to costly repairs, or worse, an accident.

Even something as simple as the glues used to hold a tire tread to the rest of the tire is an integral part of a car or truck. Just ask Firestone. That exact issue resulted in a costly recall of thousands of tires, legal recourse, as well as over 500 injuries and 148 deaths. All of which could have been prevented with only a little bit of testing. Be wary of new designs rushed into mass production.

Often a seemingly superficial part to a vehicle actually provides a significant amount of safety. Everyone knows a windshield protects the driver and passenger from wind and debris. Most also know that they are also designed with a thin film that prevents them shattering upon impact. What most people don't know is that the windshield provides over half of the structural support for the car during an impact. The windshield combined with the frame of the car makes it structurally safer than a car without one. Cracks in a windshield can greatly reduce their protective power, as well as obstruct the driver's view which is even more dangerous.

Replacing or repairing cracks and chips in a windshield should be done by trained professional at a certified and insured auto glass or body shop. Avoid independent installers and people who operate only out of their truck. The adhesive used dries in about an hour, so if any body shops quote you a turn around time less than that, they are either lying or don't know what they are doing.

Also, it is a good idea to know a little bit about the glass windshields they will be installing. There are three aftermarket windshields that exceed OEM and DOT specs, they are P.P.G., L.O.F. and Plinkington.

Other suitable windshields are made by the car factory. Ford's factory glass is called Carlite, and Chrysler's is Safeguard. Expect to pay more money for factory glass. A good auto glass installer will sand all the rust around the windshield after it is removed, and then prime and paint it before installing the new windshield. It is best to go with body shops that have been around for at least five years as they are more likely to be around to guarantee warranties and make repairs in the future. Many shops will also work with your insurance carrier to get you the best price on a windshield, sometimes completely paid for by the insurance company.

Body repair is another story and can become very expensive. Newer cars with plastic and fiberglass bodies are almost impossible to repair, the body panels are often much easier to just replace, and that can be accomplished by almost anyone with a wrench and screw driver. Repairing dents and rust on metal bodies can be time consuming as well as expensive. It also requires a matching paint job which is similarly expensive. If the dented or rusted panels can be removed it makes it much easier. Dents can be pounded back into shape. In addition to this, it is often just easier to work on and paint a detached piece. Some work can be done by the average Joe, but extensive body work should be done at an established body shop.

Body shops say insurance companies are skimping on repairs

Auto Body Collision Repair Near Me

Some of the biggest questions people run into deal with the repairing their vehicles. Many times people are confused and don't know how to go about picking the right auto body shop. What process should I run through in picking the right vehicle repair shop? What questions should I consider?

What value am I getting for my Auto Body Repair?

The most important question in determining what auto body repair shops is: What value am I getting in repairing my vehicle here? Many body shops out there are looking for unsuspecting customers and ways to pad their bottom dollar. A lot of times body shops will offer the lowest price because they know this will attract customers. Unfortunately, from a customer standpoint choosing the lowest price is not always the way to go.

Daniel T., Vice President of National Auto Parts, in Dallas, Texas, concurs that doing this will only create more car issues in the future. "Repairing your vehicle is always about what you get in return. These days, body shops continue to push the limits of their customers to see how much more they can get away with. At this point the body shop knows exactly what they're doing. Is the customer to know the better?"

What can I do to protect myself?

A solution that's been picking up a lot of traction recently is hiring a third party to assist you in this area. There are a few good car crash consultants out there that will help you figure out what's being put on your vehicle and how the vehicle's being repaired. When looking for a good car crash consultant selecting one that gives you a lot of insight on the repair and product being used is imperative. Using these specialists provides visibility in an area with many questions.

Another way is looking for a detailed report of the work being put into the vehicle and reviewing the warranty the shops offers. When you get into an accident, every insurance gives you an assessment of the damages, take a look at the sheets and read over to see what product they've listed for use. Auto Body Shops sporadically will attempt to use cheaper parts to make more money. Requesting the use of what's listed on your insurance assessment is not unusual and will help protect against this. In regards to warranties, most legitimate body shops will have an extensive warranty and stand by their work.

Where should I look for the body shop?

Driving to the nice plush auto body repair shops off the highway might be convenient, but doing this often drives up the price of the job. "All businesses have costs and are in it to make money. With this assumption, you have to believe any cost a business incurs will be passed onto their consumer," Daniel says. Hanging off the highway, and looking more in-city gives any prospective client a better chance to keep labor costs low. Prices per hour for labor can vary wildly from $30-$100 for the same type of work. Don't misunderstand the shop may not look the best, but you can be guaranteed going this route will provide good value.


Brake Check in New Jersey

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in New Jersey. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in New Jersey. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

How to Pick the Right Auto Body Repair Shops

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in New Jersey is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

Laser Wheel Alignment: Chassis Mounted Vs Wheel Mounted

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in New Jersey are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Quality Auto Body

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in New Jersey is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

What Is An Auto Body Shop?

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

Check your tire pressures before deciding whether you need wheel alignment. Opposing tires that do not have balanced tire pressure can indicate the unnecessary need for wheel alignment. Wheel alignment is the science of aligning the rear wheels to run in the same tracks as the front wheels. Correctly aligned wheels can improve the mileage tires will last by up to 10 000 kms.I was driving from Durban to Nelspruit eying the craters euphemistically referred to as potholes. I am sure I saw a Landrover fall into the one, but on closer inspection could not find any positive proof barring what looked like the tracks of some Continental tires. The bottom was not visible so we remain unsure of whether there were any survivors. Back to my point, beside the fact, that not all of us drive rugged 4x4 vehicles. Believe me, they also need realignment after a trip on those Mpumalanga roads. I got to wondering about how often it should be done. I spoke to Gary at HI-Q on my return to Nelspruit who said "It's a good idea to check your alignment every 10 - 12000 kms"If your camber or toe in are out you can wear a tire down to canvass in as little as 3000 km's. I did that once back when I hit a kerb with my Mazda tree to tree in the eighties. In essence, Gary just reinforced what I already knew. Pop into HI-Q down in Riverside Industrial Park right opposite Volvo and Land Rover on the way to the mall. Gary and his team will freely advise you if their services are essential.

What to Look for in an Auto Body Shop

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In New Jersey Should Help You With What Car Needs Exactly?

Toyo Tires For Sale

Students who graduate from Surry CommunityCollege’s Collision Repair and Refinishing Technology program can pursue careers as painttechnicians, body technicians, service writers, insurance adjusters, insurance estimators,auto detail technicians, and retail sales associates. Autobody classes are also offered to peoplewho would like to simply learn how to fix up their own vehicles as a hobby. Night classes are offered. Hello, my name is Jeff Boles, and I am theLead Instructor for Collision Repair and Refinishing Technology here at Surry Community Collegebetter known as the the Autobody program. We offer classes in painting and refinishing,nonstructural damage, structural damage, automotive MIG welding along with a plastics and adhesivesclasses. We also offer courses on special finishes,automotive detailing and autobody estimating. Diploma seeking students can choose to takea Work-Based Learning option where they can work for a company while also earning a classcredit. The Autobody students are working on a 1932Ford Roadster Project Car, which will be displayed at college and community events. Students also bring their projects from homeand can take the classes over in order to use the college equipment and facilities. Students like the flexibility of our program. We have students studying for a certificateand diploma, while some students are just taking the course for enrichment and to beable to repair their own vehicle. Students can earn a diploma or certificatein Collision Repair and Refinishing Technology and be ready for full-time employment in theAutobody industry or simply take Autobody classes for a hobby. I am a student at the Surry Early College,and I am taking the Automotive and Autobody classes. I am really enjoying the Autobody classes. I get to work on my own projects. They help me out. I am getting college credit and high schoolcredit. It’s also tuition paid. I don’t have to pay anything to take it. It’s really great for me. After I graduate, I am hoping to go into ashop. I am wanting to work for somebody for a while,and then after I get experience of how to run my own business and do my own thing, thenI want to open up my own shop. Well, behind me is a 92 Ford Ranger. I had it as my first vehicle. I wrecked it. When I wrecked it, I had a plan. My plan and my vision is to put Cummings turbodiesel in it. Right now I am fitting it to a 78 F-100 chassisand suspension. It’s got a Dana 44 straight front axle underit and a 9-inch rear, so that was already done. I don’t have to do the swaps or anythinglike that. I am just going to do a little bit of bodywork, put the Cummings in it and hopefully, it’s done. The work I do is very satisfying. I love working with my hands, and I love workingwith cars and seeing how they turn out. The instructors are very helpful. When I have a question, they are right thereto answer it. If I need something, some kind of guidance,they show me and then they let me do it. One of the reasons I chose to take Autobodyhere at Surry was that I have always wanted to paint cars give those custom paint jobs. That's one of the reasons I took it. This right here is my truck that I have beenworking on restoring it. I want to give it an aftermarket paint jobsomething that would look nice. The instructors here are helpful and knowledgeableon anything they need. They know their thing so whenever you needhelp or when you are doing something they will come and help you out. You get it done the right way. This is really exciting. You are always excited when you start somethingto get it done. I grew up as a tomboy working on a farm helpingmy paw. That’s probably what got me into likingand working on cars. I love cars. I like working in Autobody because I likeworking with my hands and working on cars and helping people. I am just going around helping people likeNancy over here. I help her a lot. The other day I helped her take an exhaustoff. I helped David sand his truck a little bit,and I been working on the school’s hotrod. I painted the bottom of it. I was just going to take automotive, but nowI have decided to take Autobody because most of these dealerships are going to have Autobodyand Automotive so that’s a double whammy. When I get out of college, graduate, I’dlike to work at a dealership. I hope to get a job at a Jeep dealership becauseI love Jeeps. Autobody professionals make about $39,000per year or more based on experience. Extremely successful Autobody shop ownerscan make in the neighborhood $60,000 to $100,000 in the Piedmont Triad area. High school juniors and seniors can take Autobodyclasses tuition-free through the Career & College Promise dual enrollment program. For more information, go to www. Surry. Edu. You can also follow the program on Facebook@SurryAutobody.

Take Control: Choose the Right Body Shop


Best Auto Body Shop in New Jersey