If you’re looking for an auto body shop in New Jersey make sure you give Peotters Tire & Auto a call as the New Jersey areas premier tire and brake shop. Today’s vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop in New Jersey to be aware of the different materials and techniques used for repairing them.
Auto body shops like Peotter’s Tire and Auto and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.
When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills.
A good, eco-friendly auto body shop in New Jersey will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.
What makes auto body shops so difficult to heat during the cold season? To shop owners, the answer is obvious. Auto body shops are characteristically dusty, breezy, high heat-loss environments. To make the indoor air more breathable and safe for workers, fresh air must be introduced through use of exhaust fans and/or raising overhead doors to help dissipate and eliminate contaminants. The problem is, as contaminants are pulled out, so is the heated air. Seemingly a "no win" scenario right?
So what's the most effective and efficient way to heat body shops?
Answer: Infrared radiant tube heaters.
To help answer that question, let's review what "infrared" is and how it works.
Infrared (IR) is electromagnetic wave energy that travels at the speed of light until it strikes an object. Upon striking an object, the IR energy converts to heat and is either reflected or absorbed. Dark and opaque objects (i.e. asphalt, concrete, etc.) readily absorb radiant IR heat energy, whereas highly reflective objects such as chrome and polished aluminum are poor absorbers and tend to reflect that energy away.
The most familiar IR emitter (heater) is our own sun. The sun radiates its IR energy through our atmosphere to the earth's surface, uninhibited by wind. As the earth's surface absorbs that energy, our air becomes warm.
During our North American winters the sun's rays are less dense due to the angle of the sun in the sky and our air temperatures are much cooler. But by summer solstice the sun's rays are at their peak angle and absorption is at its highest, resulting in warmer air temperatures.
Why use infrared tube heaters for your body shop?
1) Ceiling suspended infrared tube heaters mimic the warmth of the sun by warming up tools, machinery, floors and people directly, thereby warming the air indirectly.
2) Unlike forced air heaters, infrared tube heaters do not blow air throughout the space. That's a big plus in body shops where dust in painting areas is a problem.
3) Quicker heat recovery. As infrared energy absorbs into floors, tools, vehicles, etc., heat is recovered much more quickly when overhead doors are opened and closed again or when exhaust fans are cycled on and off periodically. That's because surfaces in the direct path of the infrared rays become a "heat sink". In other words, stored heat in objects re-radiates to warm the surrounding air.
4) Energy efficiency - an infrared tube heating system can save as much as 50% or more in fuel savings compared to conventional forced air. This is especially true in body shops where air exchanges are very high.
5) Infrared heaters can increase production. A carefully designed infrared tube heating system can be used to decrease drying times and enhance paint job quality. Placing vehicles in the path of infrared radiation warms cold metal surfaces. Paint applied to warm metal surfaces is less likely to run or drip than when applied to cold surfaces. And because infrared heaters don't move air around, there is less opportunity for dust particles to mix with newly applied paint.
We should note that gas infrared tube heaters are NOT to be used inside paint booths or paint mixing rooms. Tube heater emitters can reach 900 to 1100 Degrees F, well above the flash point of solvent-based primers and sprays. Spraying should be contained in a designated paint room with a filter bank and exhaust system to carry away potentially explosive fumes. Once spraying is done and the booth is ventilated with fresh air, vehicles and components can then be moved out of the spray booth to an isolated drying area where the infrared heaters are located.
Are some infrared tube heaters better than others for heating body shops?
That's where you need to do a bit of homework. A thorough review of the various infrared tube heater manufacturers can turn up some surprising differences between brands and product offerings. In your search, ask about burner design (are controls isolated from the air stream? They should be.), emitter tubing (heat-treated aluminized or cheaper hot-rolled steel?), reflector efficiency (50% efficient or 100%), and warranty (10 years is better than 5 years).
The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part.
Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.
Working with Plastics
The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.
It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.
Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.
The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.
Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.
Cleaning and Prep
Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.
Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.
This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.
Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.
Who Really IS the Best Auto Body Shop in New Jersey ?
Regular wheel alignments are an important part of conscientious car maintenance. Unfortunately, many car owners fail to understand the importance of good wheel alignment, and therefore don't have their alignment checked often enough.Here are five reasons why getting regular wheel alignments is good for your car, your bank account, and your peace of mind.1: Better gas mileage. When your wheels are aligned properly, it cuts down on rolling resistance, which means that you car doesn't have to work as hard or burn as much fuel in order to move forward. This is good news for everyone: Not only do you spend less money on gas, but you also get the satisfaction of knowing your car is responsible for less pollution.5: Easier to drive. One of the biggest advantages of having your wheels aligned properly is that your car is easier to drive. No annoying pull to one side or the other. It's much easier and more pleasant to drive a car that has had regular wheel alignments.As you can see, there are many reasons why a car owner should be sure to get regular wheel alignments. Not only does having your wheels aligned properly save you money on gas, tires, and other potential repairs, but it also gives you better peace of mind to know that your car is being cared for properly.
Bike Brake Overview
If you’re ever involved in an accident in a leased car, there are a few very specific things that you need to do. The first step is to call 911, even if it’s a relatively minor accident, you still need to report it to the police. That’s because insurance companies need the police report to resolve disputes about who’s at fault.
The second step is to notify your insurance company. Regardless of who’s fault it is, your insurance company will help you file your claim against the other driver. And if the other driver wasn’t insured or underinsured, your insurance company will pay for the damage, as long as your policy covers such things.
The third step is to notify your lease finance company, especially if the car was declared totaled. Since they definitely would want to know if one of their cars got destroyed and will need to talk to the insurance company.
If the vehicle can be repaired
If your car wasn’t declared totaled and can be repaired, it’s very crucial to have the work done by a professional body shop which has been approved by your insurance company. It’s also helpful if the shop is authorized and recognized as a repair shop for your particular make of the vehicle. Talk to your dealer about finding an authorized shop.
When repairing your vehicle, it needs to be done in a way that restores it to a like-new condition and uses only OEM parts. If you use substandard parts or repair shops, you run the risk of being charged at the end of your lease for any re-repair costs that will be needed to bring your vehicle to an acceptable condition.
If the vehicle is totaled
If the necessary repair costs exceed 70% of the vehicle’s value, that it will be considered a total loss. In this case, the insurance company will pay the market value of the car to your lease finance company.
If you get lucky and your lease buyout balance exceeds the payout from the insurance company, the lease company may possibly refund the difference to you. But this rarely happens with leases.
Majority of the time, the payout from the insurance company is less than the lease balance, which leaves a deficiency that you will be responsible to cover. The good news is that most lease contracts require GAP insurance, which would cover that deficiency.
So where does this leave you?
If your leased vehicle can be repaired and you have the repairs done then proceed with your lease as normal and return the car once the lease ends. There’s one note of caution, however. Whenever a vehicle is involved in an accident, the trade and resale value gets reduced. Sometimes the insurance company may give you or the lease company a “diminished value” payment.
If your leased vehicle is totaled, then your basically left without a car, the same as if you returned your car at the end of a lease. If your car was over the mileage limit when the accident happened then you will still be charged for the extra miles as you normally would at the end of your lease. Might not seem fair to you but the lease company see’s it otherwise.
If you’ll need a replacement car
If the leased car gets totaled and you need another vehicle, you will need to start over with a new car lease or simply buy another car.
So, if you ever get into an accident in your leased car, first call 911, then your insurance company, and your lease company last. What happens next will largely depend on the severity of the accident, repair costs, and your insurance coverage policy. And it’s possible that you might end up owning more money to the lease company.
- Brake Check in New Jersey
- Tire Repair in Summit
- Auto Body Shop in New Providence
- Tire Repair in Berkeley Heights
- Brake Check in Mountainside
- Brake Repair in Chatham
- Tire Repair in Madison
- Tire Repair in Springfield
- Brake Repair in Maplewood
- Brake Check in Vauxhall
- Best Auto Body Shop in Short Hills
- Brake Repair in Kenilworth
- Tire and Brakes in South Orange
- Tires and Brakes in Morristown
- Tire and Brakes in Florham Park
- Tire Repair in Livingston
- Auto Body Shop in Union