Brake Check in Vauxhall

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in Vauxhall. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in Vauxhall. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

Auto Body Shops - Few Tips For Dealing With Them

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in Vauxhall is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

Auto Body Shops - Bumper Repair Vs Bumper Replacement

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in Vauxhall are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Paint My Car

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in Vauxhall is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

Fake Auto Body Repair Scheme Targets Victims With Dents In Cars

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

What makes auto body shops so difficult to heat during the cold season? To shop owners, the answer is obvious. Auto body shops are characteristically dusty, breezy, high heat-loss environments. To make the indoor air more breathable and safe for workers, fresh air must be introduced through use of exhaust fans and/or raising overhead doors to help dissipate and eliminate contaminants. The problem is, as contaminants are pulled out, so is the heated air. Seemingly a "no win" scenario right?

So what's the most effective and efficient way to heat body shops?

Answer: Infrared radiant tube heaters.

Why Infrared?

To help answer that question, let's review what "infrared" is and how it works.

Infrared (IR) is electromagnetic wave energy that travels at the speed of light until it strikes an object. Upon striking an object, the IR energy converts to heat and is either reflected or absorbed. Dark and opaque objects (i.e. asphalt, concrete, etc.) readily absorb radiant IR heat energy, whereas highly reflective objects such as chrome and polished aluminum are poor absorbers and tend to reflect that energy away.

The most familiar IR emitter (heater) is our own sun. The sun radiates its IR energy through our atmosphere to the earth's surface, uninhibited by wind. As the earth's surface absorbs that energy, our air becomes warm.

During our North American winters the sun's rays are less dense due to the angle of the sun in the sky and our air temperatures are much cooler. But by summer solstice the sun's rays are at their peak angle and absorption is at its highest, resulting in warmer air temperatures.

Why use infrared tube heaters for your body shop?

1) Ceiling suspended infrared tube heaters mimic the warmth of the sun by warming up tools, machinery, floors and people directly, thereby warming the air indirectly.

2) Unlike forced air heaters, infrared tube heaters do not blow air throughout the space. That's a big plus in body shops where dust in painting areas is a problem.

3) Quicker heat recovery. As infrared energy absorbs into floors, tools, vehicles, etc., heat is recovered much more quickly when overhead doors are opened and closed again or when exhaust fans are cycled on and off periodically. That's because surfaces in the direct path of the infrared rays become a "heat sink". In other words, stored heat in objects re-radiates to warm the surrounding air.

4) Energy efficiency - an infrared tube heating system can save as much as 50% or more in fuel savings compared to conventional forced air. This is especially true in body shops where air exchanges are very high.

5) Infrared heaters can increase production. A carefully designed infrared tube heating system can be used to decrease drying times and enhance paint job quality. Placing vehicles in the path of infrared radiation warms cold metal surfaces. Paint applied to warm metal surfaces is less likely to run or drip than when applied to cold surfaces. And because infrared heaters don't move air around, there is less opportunity for dust particles to mix with newly applied paint.

We should note that gas infrared tube heaters are NOT to be used inside paint booths or paint mixing rooms. Tube heater emitters can reach 900 to 1100 Degrees F, well above the flash point of solvent-based primers and sprays. Spraying should be contained in a designated paint room with a filter bank and exhaust system to carry away potentially explosive fumes. Once spraying is done and the booth is ventilated with fresh air, vehicles and components can then be moved out of the spray booth to an isolated drying area where the infrared heaters are located.

Are some infrared tube heaters better than others for heating body shops?

Yes indeed.

That's where you need to do a bit of homework. A thorough review of the various infrared tube heater manufacturers can turn up some surprising differences between brands and product offerings. In your search, ask about burner design (are controls isolated from the air stream? They should be.), emitter tubing (heat-treated aluminized or cheaper hot-rolled steel?), reflector efficiency (50% efficient or 100%), and warranty (10 years is better than 5 years).

The Importance of Proper Wheel Alignment

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In Vauxhall Should Help You With What Car Needs Exactly?

Tire Repair Places Near Me

A car is a very complex piece of machinery. Each individual part is vigorously tested before it ever goes into production models and, like a chain, relies upon every other part in order for the vehicle to function. One poorly built aspect can cause serious malfunctions leading to costly repairs, or worse, an accident.

Even something as simple as the glues used to hold a tire tread to the rest of the tire is an integral part of a car or truck. Just ask Firestone. That exact issue resulted in a costly recall of thousands of tires, legal recourse, as well as over 500 injuries and 148 deaths. All of which could have been prevented with only a little bit of testing. Be wary of new designs rushed into mass production.

Often a seemingly superficial part to a vehicle actually provides a significant amount of safety. Everyone knows a windshield protects the driver and passenger from wind and debris. Most also know that they are also designed with a thin film that prevents them shattering upon impact. What most people don't know is that the windshield provides over half of the structural support for the car during an impact. The windshield combined with the frame of the car makes it structurally safer than a car without one. Cracks in a windshield can greatly reduce their protective power, as well as obstruct the driver's view which is even more dangerous.

Replacing or repairing cracks and chips in a windshield should be done by trained professional at a certified and insured auto glass or body shop. Avoid independent installers and people who operate only out of their truck. The adhesive used dries in about an hour, so if any body shops quote you a turn around time less than that, they are either lying or don't know what they are doing.

Also, it is a good idea to know a little bit about the glass windshields they will be installing. There are three aftermarket windshields that exceed OEM and DOT specs, they are P.P.G., L.O.F. and Plinkington.

Other suitable windshields are made by the car factory. Ford's factory glass is called Carlite, and Chrysler's is Safeguard. Expect to pay more money for factory glass. A good auto glass installer will sand all the rust around the windshield after it is removed, and then prime and paint it before installing the new windshield. It is best to go with body shops that have been around for at least five years as they are more likely to be around to guarantee warranties and make repairs in the future. Many shops will also work with your insurance carrier to get you the best price on a windshield, sometimes completely paid for by the insurance company.

Body repair is another story and can become very expensive. Newer cars with plastic and fiberglass bodies are almost impossible to repair, the body panels are often much easier to just replace, and that can be accomplished by almost anyone with a wrench and screw driver. Repairing dents and rust on metal bodies can be time consuming as well as expensive. It also requires a matching paint job which is similarly expensive. If the dented or rusted panels can be removed it makes it much easier. Dents can be pounded back into shape. In addition to this, it is often just easier to work on and paint a detached piece. Some work can be done by the average Joe, but extensive body work should be done at an established body shop.

Wheel Alignment and Tire Balancing: Why Are They Important?


Best Auto Body Shop in New Jersey