Tire Repair in Springfield

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in Springfield. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in Springfield. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

How to Pick the Right Auto Body Repair Shops

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in Springfield is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

Wheel Alignment Tech Talk - Camber, Caster, Toe-in

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in Springfield are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Best Tire Prices

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in Springfield is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

Secrets of the Auto Body Shop

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

What makes auto body shops so difficult to heat during the cold season? To shop owners, the answer is obvious. Auto body shops are characteristically dusty, breezy, high heat-loss environments. To make the indoor air more breathable and safe for workers, fresh air must be introduced through use of exhaust fans and/or raising overhead doors to help dissipate and eliminate contaminants. The problem is, as contaminants are pulled out, so is the heated air. Seemingly a "no win" scenario right?

So what's the most effective and efficient way to heat body shops?

Answer: Infrared radiant tube heaters.

Why Infrared?

To help answer that question, let's review what "infrared" is and how it works.

Infrared (IR) is electromagnetic wave energy that travels at the speed of light until it strikes an object. Upon striking an object, the IR energy converts to heat and is either reflected or absorbed. Dark and opaque objects (i.e. asphalt, concrete, etc.) readily absorb radiant IR heat energy, whereas highly reflective objects such as chrome and polished aluminum are poor absorbers and tend to reflect that energy away.

The most familiar IR emitter (heater) is our own sun. The sun radiates its IR energy through our atmosphere to the earth's surface, uninhibited by wind. As the earth's surface absorbs that energy, our air becomes warm.

During our North American winters the sun's rays are less dense due to the angle of the sun in the sky and our air temperatures are much cooler. But by summer solstice the sun's rays are at their peak angle and absorption is at its highest, resulting in warmer air temperatures.

Why use infrared tube heaters for your body shop?

1) Ceiling suspended infrared tube heaters mimic the warmth of the sun by warming up tools, machinery, floors and people directly, thereby warming the air indirectly.

2) Unlike forced air heaters, infrared tube heaters do not blow air throughout the space. That's a big plus in body shops where dust in painting areas is a problem.

3) Quicker heat recovery. As infrared energy absorbs into floors, tools, vehicles, etc., heat is recovered much more quickly when overhead doors are opened and closed again or when exhaust fans are cycled on and off periodically. That's because surfaces in the direct path of the infrared rays become a "heat sink". In other words, stored heat in objects re-radiates to warm the surrounding air.

4) Energy efficiency - an infrared tube heating system can save as much as 50% or more in fuel savings compared to conventional forced air. This is especially true in body shops where air exchanges are very high.

5) Infrared heaters can increase production. A carefully designed infrared tube heating system can be used to decrease drying times and enhance paint job quality. Placing vehicles in the path of infrared radiation warms cold metal surfaces. Paint applied to warm metal surfaces is less likely to run or drip than when applied to cold surfaces. And because infrared heaters don't move air around, there is less opportunity for dust particles to mix with newly applied paint.

We should note that gas infrared tube heaters are NOT to be used inside paint booths or paint mixing rooms. Tube heater emitters can reach 900 to 1100 Degrees F, well above the flash point of solvent-based primers and sprays. Spraying should be contained in a designated paint room with a filter bank and exhaust system to carry away potentially explosive fumes. Once spraying is done and the booth is ventilated with fresh air, vehicles and components can then be moved out of the spray booth to an isolated drying area where the infrared heaters are located.

Are some infrared tube heaters better than others for heating body shops?

Yes indeed.

That's where you need to do a bit of homework. A thorough review of the various infrared tube heater manufacturers can turn up some surprising differences between brands and product offerings. In your search, ask about burner design (are controls isolated from the air stream? They should be.), emitter tubing (heat-treated aluminized or cheaper hot-rolled steel?), reflector efficiency (50% efficient or 100%), and warranty (10 years is better than 5 years).

Body shops say insurance companies are skimping on repairs

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In Springfield Should Help You With What Car Needs Exactly?

Best Tire Prices

What is a wheel alignment? How does it effect handling and tire wear? When should I do an alignment? What causes alignments to go out? How would I know if my alignment is out?  A wheel alignment is nothing more than setting the angle of the hub/wheel so it tracks in the right direction. Most vehicles have four-wheel alignments, meaning each of the four wheels is separately aligned.  Your basic alignment consists of three angles: camber, caster  and toe-in. Camber is the tilt of the tire when viewed from the front of the car. Positive camber means the top of the tire is tilted away from the car. Negative camber means the top is tilted in. Camber has a lot to do with cornering performance. Too much negative camber will wear the inside of the tires prematurely. Too much positive camber will wear the outside tread. Caster is the inclination of the front spindle. Picture the angle of the forks on a bike top to bottom. When the caster is out, it creates a pull or wandering condition and sometimes a slow responding steering wheel. Toe-in is measured in inches or degrees. Viewing from the front of the car, it is the difference between the front and rear center-line of the tire. Toe-in means the fronts of the tires are closer together. Toe-out means, the fronts of the tires are farther apart. Toe-in or out has the most effect on tire wear. There is a lot more to suspension alignment, especially if you push your vehicle on the track. The modifications you make on your suspension are just the beginning. Once you start down this road you will be concerned with things like bump steer, weighting (vertical load), preloading, tire traction versus tire load, and more. Now you're thinking under-steer, over-steer, tire compound, sway bar design, and other topics that can be covered in a later article. For now, just remember to have your vehicle aligned every 10,000 to 12,000 miles in normal driving conditions.If you accidentally hit a curb, or drive through a nasty pothole or other road obstruction, that would be a cue to have your car's alignment checked more often. Proper alignment is good for your car. It will save unnecessary wear on your tires. It will ensure that your vehicle is giving you the handling the factory designed the car to have. And, most importantly, a properly aligned car is safer and more fun to drive.   

Prevent Common Problems with Body Filler


Best Auto Body Shop in New Jersey