It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in Short Hills. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.
What is the next step after your collision and you need an auto body shop?
Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.
Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in Short Hills.
They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.
This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.
Mountain Bike Travel: Things You Should Never Forget
Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.
Now here are some things to watch out for. a local auto body shop in Short Hills is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.
How to Find Auto Body Shops
Replacement Parts in Auto Body Shops
Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in Short Hills are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.
Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.
No Realignment? Talk to Your Auto Repair Team!
The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.
Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.
Using Bondo (Fillers) Instead of Replacing the Part
Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in Short Hills is doing, they tell you, and this is what you are paying for then it is fine.
The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.
All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!
Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.
What makes auto body shops so difficult to heat during the cold season? To shop owners, the answer is obvious. Auto body shops are characteristically dusty, breezy, high heat-loss environments. To make the indoor air more breathable and safe for workers, fresh air must be introduced through use of exhaust fans and/or raising overhead doors to help dissipate and eliminate contaminants. The problem is, as contaminants are pulled out, so is the heated air. Seemingly a "no win" scenario right?
So what's the most effective and efficient way to heat body shops?
Answer: Infrared radiant tube heaters.
To help answer that question, let's review what "infrared" is and how it works.
Infrared (IR) is electromagnetic wave energy that travels at the speed of light until it strikes an object. Upon striking an object, the IR energy converts to heat and is either reflected or absorbed. Dark and opaque objects (i.e. asphalt, concrete, etc.) readily absorb radiant IR heat energy, whereas highly reflective objects such as chrome and polished aluminum are poor absorbers and tend to reflect that energy away.
The most familiar IR emitter (heater) is our own sun. The sun radiates its IR energy through our atmosphere to the earth's surface, uninhibited by wind. As the earth's surface absorbs that energy, our air becomes warm.
During our North American winters the sun's rays are less dense due to the angle of the sun in the sky and our air temperatures are much cooler. But by summer solstice the sun's rays are at their peak angle and absorption is at its highest, resulting in warmer air temperatures.
Why use infrared tube heaters for your body shop?
1) Ceiling suspended infrared tube heaters mimic the warmth of the sun by warming up tools, machinery, floors and people directly, thereby warming the air indirectly.
2) Unlike forced air heaters, infrared tube heaters do not blow air throughout the space. That's a big plus in body shops where dust in painting areas is a problem.
3) Quicker heat recovery. As infrared energy absorbs into floors, tools, vehicles, etc., heat is recovered much more quickly when overhead doors are opened and closed again or when exhaust fans are cycled on and off periodically. That's because surfaces in the direct path of the infrared rays become a "heat sink". In other words, stored heat in objects re-radiates to warm the surrounding air.
4) Energy efficiency - an infrared tube heating system can save as much as 50% or more in fuel savings compared to conventional forced air. This is especially true in body shops where air exchanges are very high.
5) Infrared heaters can increase production. A carefully designed infrared tube heating system can be used to decrease drying times and enhance paint job quality. Placing vehicles in the path of infrared radiation warms cold metal surfaces. Paint applied to warm metal surfaces is less likely to run or drip than when applied to cold surfaces. And because infrared heaters don't move air around, there is less opportunity for dust particles to mix with newly applied paint.
We should note that gas infrared tube heaters are NOT to be used inside paint booths or paint mixing rooms. Tube heater emitters can reach 900 to 1100 Degrees F, well above the flash point of solvent-based primers and sprays. Spraying should be contained in a designated paint room with a filter bank and exhaust system to carry away potentially explosive fumes. Once spraying is done and the booth is ventilated with fresh air, vehicles and components can then be moved out of the spray booth to an isolated drying area where the infrared heaters are located.
Are some infrared tube heaters better than others for heating body shops?
That's where you need to do a bit of homework. A thorough review of the various infrared tube heater manufacturers can turn up some surprising differences between brands and product offerings. In your search, ask about burner design (are controls isolated from the air stream? They should be.), emitter tubing (heat-treated aluminized or cheaper hot-rolled steel?), reflector efficiency (50% efficient or 100%), and warranty (10 years is better than 5 years).
The Importance of Proper Wheel Alignment
The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.
Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.
Your Auto Body Shop In Short Hills Should Help You With What Car Needs Exactly?
For the majority of drivers, going to an auto body shop is a mysterious experience, a scary encounter with the unknown. Once you hand over your key, you instantly feel uneasy; will your car be returned as good as new, or will the repair specialists do a shoddy job? How will you know? How will you be able to figure out if you hard-earned money is just being tossed down the drain?
The best way to know if you are receiving excellent service and professional care is to find a reputable body shop and then build a relationship with that shop. However, most people who take their vehicles in to the shop are doing so for the first time. So, how do you know whether or not you can trust an auto body shop?
First of all, it is important to know that most auto body shops are reputable businesses. The majority of auto shop owners are just struggling to make a living like most small business owners - they want to do a great job on your car so you will return or refer others to their shop. However, there are a few bad apples that spoil the whole bunch, and you need to be diligent when selecting a shop.
The first thing to do is get a referral or locate a shop online using reviews and testimonials. Create a list and call each shop to see how well you are treated on the phone. Select three or four shops that sound good and are in close proximity to your location, and you are ready to take your vehicle in for an estimate.
You should get at least three estimates from three different shops. The estimate may vary because shops may use different estimating software, but they should all be in the same ballpark. If an estimate differs by a great deal, you should ask why. The body shop expert should be able to explain all prices on the estimate, including all price quotes and labor charges.
When you get the estimate, you should also be evaluating the customer service. How quickly were you acknowledged? How efficiently were you helped? Were all members of the staff polite and friendly? Did the staff seem knowledgeable? Be observant during the estimate and you will have a good idea of how you will be treated during the entire repair process. If the customer service seems lacking, move on to the next place even if the estimate seems reasonable.
If you decide to leave your car, and the shop contacts you later to tell you about additional charges, this may be a sign that it is not a reputable and honest repair facility. Though additional charges can happen occasionally, it is not a common practice for a reputable shop.
If you do your homework, have some patience, and get a few estimate, the odds are good that you will find a reputable auto body shop. Once you have found one, it helps to direct all your business to them, and refer them to others. If you do this, you will have established a good relationship, and you will no longer need to worry about finding an honest auto body shop.