Best Auto Body Shop in New Jersey

If you’re looking for an auto body shop in New Jersey make sure you give Peotters Tire & Auto a call as the New Jersey areas premier tire and brake shop. Today’s vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop in New Jersey to be aware of the different materials and techniques used for repairing them.

Auto body shops like Peotter’s Tire and Auto and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills.

A good, eco-friendly auto body shop in New Jersey will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

Check your tire pressures before deciding whether you need wheel alignment. Opposing tires that do not have balanced tire pressure can indicate the unnecessary need for wheel alignment. Wheel alignment is the science of aligning the rear wheels to run in the same tracks as the front wheels. Correctly aligned wheels can improve the mileage tires will last by up to 10 000 kms.I was driving from Durban to Nelspruit eying the craters euphemistically referred to as potholes. I am sure I saw a Landrover fall into the one, but on closer inspection could not find any positive proof barring what looked like the tracks of some Continental tires. The bottom was not visible so we remain unsure of whether there were any survivors. Back to my point, beside the fact, that not all of us drive rugged 4x4 vehicles. Believe me, they also need realignment after a trip on those Mpumalanga roads. I got to wondering about how often it should be done. I spoke to Gary at HI-Q on my return to Nelspruit who said "It's a good idea to check your alignment every 10 - 12000 kms"If your camber or toe in are out you can wear a tire down to canvass in as little as 3000 km's. I did that once back when I hit a kerb with my Mazda tree to tree in the eighties. In essence, Gary just reinforced what I already knew. Pop into HI-Q down in Riverside Industrial Park right opposite Volvo and Land Rover on the way to the mall. Gary and his team will freely advise you if their services are essential.

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part.

Auto Body Collision Repair Near Me

Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.

Who Really IS the Best Auto Body Shop in New Jersey ?

Used Car Tires

Before you try to run out and find auto body shops near you, take a moment to read through this article and consider including some of my personal experience as a mechanic into your own personal deliberation about what constitutes the best auto body shops in business. When you break things down, there are really two types of garages in business: good ones and bad ones. The best place to start when trying to scope out a potential body shop is the owner. In bad auto body garages the owner usually instructs the employees to give the impression that your car is in worse shape then you think, or that something is broken and needs to be fixed right away. In a legitimate auto body garage, the owner is more concerned with forging a long standing relationship with you and getting your repeat business rather then just ripping you off and potentially never seeing you again.The reason why most owners are concerned with ripping people off, especially in a body shop, is because the only two reasons cars ever go in there is for repairs on collision damage or for custom work; this means that the owners of the shop realistically do not see the owners of vehicles too often and do not see the value in repeat business, they would rather try to squeeze every dime out of your while you are there.The best auto and body shop you can ever find is where the owner looks to develop long term relationships with their clients. While it is true they can potentially never see a newer customer again, these owners are smart and do the best work possible not only to help you out, but to impress you and have you refer your friends and family to him or her. These owners are less interesting in gouging your wallet and more interested in establishing a reputation in their local community for outstanding work and service. These types of people see the value in what it means to be a true professional and are more successful then their more selfish friends in the business.The best way you figure out which owners are the good or bad guys is either by your own direct experience or the experience of others. You should not be afraid to talk to the auto body shop manager directly and begin to get a feeling for what he is about. After a short conversation and carefully studying his body movement and language, the first impression you get is often the right one.

What Are Collision Services? How Do They Work?

Best Truck Tires

Jeff what are the three questions should ask a body shop before they consider dropping their car off for repairs? Well what's important is that the repair shop actually be qualified to fix that particular vehicle.

Today modern cars require specialized training and equipment to be able to perform repairs to the manufacturer's standards.

For instance, this Mini Cooper and other BMWs require what's called rivet bonding.

So, glue joints and rivets.

They're actually repaired like aircraft today.

This is important because this maintains the structural integrity the manufacturer designed for a repair situation.

Like this fixture frame bench here that utilizes actual jigs to support the vehicle across its entire platform and place factory components precisely where the manufacturer has designated.

These systems are different than generic systems that simply are reverse engineered and don't have jig and holding capacity.

Shops that aren't trained and equipped to properly perform a repair utilizing generic equipment or generic procedures can't restore the vehicle to the manufacturer's standards and that doesn't necessarily maintain the safety ratingdesigned for the vehicle.

You potentially jeopardize the collision energy management system.

The vehicle might not perform the same in a future collision and you could possibly be more injured than you would if the car doesn't perform as the manufacturer intended.

The second question a consumer should ask is "Where does the body shop's loyalty lie?" Is it an independent repair center that relies on satisfied customers to drive business through their door and therefore fixes vehicles correctly? Or is the body shop on the insurance company's "preferred network?" Those body shops rely on the insurance referrals and when those body shops utilize cheap, imitation, and savage parts utilize the quickest possible repair times and keep costs as low as possible that generates the next referral.

But that's a recipe for shortcuts.

The third question, Paul, is "Can the repair shop make this process convenient for me?" Most consumers today want convenience and ease.

Repair shops that are high-quality repair shops are going to put their customers' interests first & do everything they can to have a satisfied customer.

That includes sheduling a rental car, scheduling a tow engaging in conversations with the insurance company and making sure the vehicle is fixed right for the consumer.


Brake Check in New Jersey

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in New Jersey. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in New Jersey. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

Wheel Alignment Tech Talk - Camber, Caster, Toe-in

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in New Jersey is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

What Is An Damage Repair Estimate? - Auto Estimating Part 1

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in New Jersey are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Tire Storage

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in New Jersey is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

How to Find Auto Body Shops

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

Some of the biggest questions people run into deal with the repairing their vehicles. Many times people are confused and don't know how to go about picking the right auto body shop. What process should I run through in picking the right vehicle repair shop? What questions should I consider?

What value am I getting for my Auto Body Repair?

The most important question in determining what auto body repair shops is: What value am I getting in repairing my vehicle here? Many body shops out there are looking for unsuspecting customers and ways to pad their bottom dollar. A lot of times body shops will offer the lowest price because they know this will attract customers. Unfortunately, from a customer standpoint choosing the lowest price is not always the way to go.

Daniel T., Vice President of National Auto Parts, in Dallas, Texas, concurs that doing this will only create more car issues in the future. "Repairing your vehicle is always about what you get in return. These days, body shops continue to push the limits of their customers to see how much more they can get away with. At this point the body shop knows exactly what they're doing. Is the customer to know the better?"

What can I do to protect myself?

A solution that's been picking up a lot of traction recently is hiring a third party to assist you in this area. There are a few good car crash consultants out there that will help you figure out what's being put on your vehicle and how the vehicle's being repaired. When looking for a good car crash consultant selecting one that gives you a lot of insight on the repair and product being used is imperative. Using these specialists provides visibility in an area with many questions.

Another way is looking for a detailed report of the work being put into the vehicle and reviewing the warranty the shops offers. When you get into an accident, every insurance gives you an assessment of the damages, take a look at the sheets and read over to see what product they've listed for use. Auto Body Shops sporadically will attempt to use cheaper parts to make more money. Requesting the use of what's listed on your insurance assessment is not unusual and will help protect against this. In regards to warranties, most legitimate body shops will have an extensive warranty and stand by their work.

Where should I look for the body shop?

Driving to the nice plush auto body repair shops off the highway might be convenient, but doing this often drives up the price of the job. "All businesses have costs and are in it to make money. With this assumption, you have to believe any cost a business incurs will be passed onto their consumer," Daniel says. Hanging off the highway, and looking more in-city gives any prospective client a better chance to keep labor costs low. Prices per hour for labor can vary wildly from $30-$100 for the same type of work. Don't misunderstand the shop may not look the best, but you can be guaranteed going this route will provide good value.

Bike Brake Overview

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In New Jersey Should Help You With What Car Needs Exactly?

Autobody Repair

The nation's top mechanics are rejecting the recommendation by some in the auto field that cars can go 5,000 miles or more before oil is changed. National Institute for Auto-motive Service Excellence (ASE)-certified Master Automobile technicians weighed in on this and other issues in a survey conducted by Valvoline. The survey covered the controversial recommendation and trend toward longer intervals between oil changes, as well as the costs to car owners of delayed maintenance. "Certified Master Automobile Technicians are the best of the best," said ASE President Ron Weiner. "They are on the front lines of taking care of today's vehicles and they have definite thoughts on how motorists can participate in making their cars and trucks run better and last longer." Oil Change Frequency Mechanics view oil as the lifeblood of the car engine, with 84 percent saying not getting a regular oil change can cause the most problems for a vehicle, when compared to other maintenance issues. Sixty percent said the oil should be changed at 3,000 miles-the longtime, recommended standard. According to the survey, Valvoline remains the number one choice of ASE Master Automobile Technicians for use in their own cars and trucks, and is the brand of motor oil most recommended by them to customers, friends and relatives. "Changing oil with quality motor oil, like Valvoline, at regular intervals is the best way to prevent damage to your car's engine and keep more money in your pocket," said Valvoline Marketing Director Bryan Emrich. He added that regular oil changes protect the engine and reduce sludge, which can impact engine perfor-mance and cause costly repairs. Delayed Car Maintenance While car owners know, intellectually and intuitively, that regular maintenance is important to keeping their four-wheeled investment in safe condition and working order, the reality is that more and more Americans are not listening to conventional and proven wisdom. The vast majority of mechanics-87 percent-said they believe American car owners are putting off routine maintenance, mostly for cost reasons. Ironically, they overwhelmingly said-at 97 percent-that delayed care will cost an owner much more in the long run, as problems left unattended can multiply and lead to other issues.

5 Benefits of Wheel Alignments - Why to Get Your Wheels Aligned Regularly


Best Auto Body Shop in New Jersey