Best Auto Body Shop in New Jersey

If you’re looking for an auto body shop in New Jersey make sure you give Peotters Tire & Auto a call as the New Jersey areas premier tire and brake shop. Today’s vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop in New Jersey to be aware of the different materials and techniques used for repairing them.

Auto body shops like Peotter’s Tire and Auto and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills.

A good, eco-friendly auto body shop in New Jersey will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

Laser Wheel Alignment SystemsLaser Wheel Alignment Systems are a modern approach to wheel alignment. Wheel alignment certainly is one of the most significant setup parameters for racing cars. You would ask why... Because even things like moment center location and setup balance lose their importance, compared to wheel alignment. The alignment package has a massive amount of influence on the way that a race car behaves and performs.One of the most common questions asked is which is best - wheel mounted or chassis mounted lasers? Answering such a query is not easy: a more precise question would be which laser wheel alignment method is better for accuracy. Then, we would have to say that the chassis mounted laser is the right answer. As to why it is so, please find below...The Wheel Mounted LaserThe wheel mounted laser is very much likely to give mounting inaccuracies. Even if the hub or spindle adapter is flawless, it's still extremely probable to have a burr on the hub or spindle face. Consider the following scenario: a simple piece of silicone 0.010" thick left on the rear hub face will throw the laser off by 0.332" by the time it reaches the leading edge of the front tire. Moreover, once we mount the laser to the wheel, that wheel now becomes the "master" reference point. In order to apply this method with accuracy, you will have to first check axle tube straightness, and then test rear end placement or wheel alignment. This rule is valid for all wheel mounted systems. On the other hand, what is also true for wheel mounted lasers is that the further you project the laser, the more accuracy you will gain. Still, in case that your mounting surface and adapters are not absolutely perfect, you will observe more inaccuracy again.Mounting the lasers to the chassis also enables the user to make suspension adjustments and read the changes instantly. For example, if you decide to adjust a trailing arm or a panhard bar, you can watch the rear end location change as you turn the tubes. Your adjustment moves the chassis, which has the lasers attached to it. Once you square the lasers to the chassis, you can make any adjustment to the suspension and the lasers stay square.Finally, it would be best to look for laser wheel alignment systems that have chassis mounted lasers that are adjustable. Having adjustable lasers allows the user to tune the laser to the master reference points, while also eliminating the possibility of a laser being "out of calibration".

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part.

Direct Tire

Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.

Who Really IS the Best Auto Body Shop in New Jersey ?

Where To Buy Tires

What makes auto body shops so difficult to heat during the cold season? To shop owners, the answer is obvious. Auto body shops are characteristically dusty, breezy, high heat-loss environments. To make the indoor air more breathable and safe for workers, fresh air must be introduced through use of exhaust fans and/or raising overhead doors to help dissipate and eliminate contaminants. The problem is, as contaminants are pulled out, so is the heated air. Seemingly a "no win" scenario right?

So what's the most effective and efficient way to heat body shops?

Answer: Infrared radiant tube heaters.

Why Infrared?

To help answer that question, let's review what "infrared" is and how it works.

Infrared (IR) is electromagnetic wave energy that travels at the speed of light until it strikes an object. Upon striking an object, the IR energy converts to heat and is either reflected or absorbed. Dark and opaque objects (i.e. asphalt, concrete, etc.) readily absorb radiant IR heat energy, whereas highly reflective objects such as chrome and polished aluminum are poor absorbers and tend to reflect that energy away.

The most familiar IR emitter (heater) is our own sun. The sun radiates its IR energy through our atmosphere to the earth's surface, uninhibited by wind. As the earth's surface absorbs that energy, our air becomes warm.

During our North American winters the sun's rays are less dense due to the angle of the sun in the sky and our air temperatures are much cooler. But by summer solstice the sun's rays are at their peak angle and absorption is at its highest, resulting in warmer air temperatures.

Why use infrared tube heaters for your body shop?

1) Ceiling suspended infrared tube heaters mimic the warmth of the sun by warming up tools, machinery, floors and people directly, thereby warming the air indirectly.

2) Unlike forced air heaters, infrared tube heaters do not blow air throughout the space. That's a big plus in body shops where dust in painting areas is a problem.

3) Quicker heat recovery. As infrared energy absorbs into floors, tools, vehicles, etc., heat is recovered much more quickly when overhead doors are opened and closed again or when exhaust fans are cycled on and off periodically. That's because surfaces in the direct path of the infrared rays become a "heat sink". In other words, stored heat in objects re-radiates to warm the surrounding air.

4) Energy efficiency - an infrared tube heating system can save as much as 50% or more in fuel savings compared to conventional forced air. This is especially true in body shops where air exchanges are very high.

5) Infrared heaters can increase production. A carefully designed infrared tube heating system can be used to decrease drying times and enhance paint job quality. Placing vehicles in the path of infrared radiation warms cold metal surfaces. Paint applied to warm metal surfaces is less likely to run or drip than when applied to cold surfaces. And because infrared heaters don't move air around, there is less opportunity for dust particles to mix with newly applied paint.

We should note that gas infrared tube heaters are NOT to be used inside paint booths or paint mixing rooms. Tube heater emitters can reach 900 to 1100 Degrees F, well above the flash point of solvent-based primers and sprays. Spraying should be contained in a designated paint room with a filter bank and exhaust system to carry away potentially explosive fumes. Once spraying is done and the booth is ventilated with fresh air, vehicles and components can then be moved out of the spray booth to an isolated drying area where the infrared heaters are located.

Are some infrared tube heaters better than others for heating body shops?

Yes indeed.

That's where you need to do a bit of homework. A thorough review of the various infrared tube heater manufacturers can turn up some surprising differences between brands and product offerings. In your search, ask about burner design (are controls isolated from the air stream? They should be.), emitter tubing (heat-treated aluminized or cheaper hot-rolled steel?), reflector efficiency (50% efficient or 100%), and warranty (10 years is better than 5 years).

Watch A Full Body Shop Repair In 90 Seconds

Repairable Vehicles

Students who graduate from Surry CommunityCollege’s Collision Repair and Refinishing Technology program can pursue careers as painttechnicians, body technicians, service writers, insurance adjusters, insurance estimators,auto detail technicians, and retail sales associates. Autobody classes are also offered to peoplewho would like to simply learn how to fix up their own vehicles as a hobby. Night classes are offered. Hello, my name is Jeff Boles, and I am theLead Instructor for Collision Repair and Refinishing Technology here at Surry Community Collegebetter known as the the Autobody program. We offer classes in painting and refinishing,nonstructural damage, structural damage, automotive MIG welding along with a plastics and adhesivesclasses. We also offer courses on special finishes,automotive detailing and autobody estimating. Diploma seeking students can choose to takea Work-Based Learning option where they can work for a company while also earning a classcredit. The Autobody students are working on a 1932Ford Roadster Project Car, which will be displayed at college and community events. Students also bring their projects from homeand can take the classes over in order to use the college equipment and facilities. Students like the flexibility of our program. We have students studying for a certificateand diploma, while some students are just taking the course for enrichment and to beable to repair their own vehicle. Students can earn a diploma or certificatein Collision Repair and Refinishing Technology and be ready for full-time employment in theAutobody industry or simply take Autobody classes for a hobby. I am a student at the Surry Early College,and I am taking the Automotive and Autobody classes. I am really enjoying the Autobody classes. I get to work on my own projects. They help me out. I am getting college credit and high schoolcredit. It’s also tuition paid. I don’t have to pay anything to take it. It’s really great for me. After I graduate, I am hoping to go into ashop. I am wanting to work for somebody for a while,and then after I get experience of how to run my own business and do my own thing, thenI want to open up my own shop. Well, behind me is a 92 Ford Ranger. I had it as my first vehicle. I wrecked it. When I wrecked it, I had a plan. My plan and my vision is to put Cummings turbodiesel in it. Right now I am fitting it to a 78 F-100 chassisand suspension. It’s got a Dana 44 straight front axle underit and a 9-inch rear, so that was already done. I don’t have to do the swaps or anythinglike that. I am just going to do a little bit of bodywork, put the Cummings in it and hopefully, it’s done. The work I do is very satisfying. I love working with my hands, and I love workingwith cars and seeing how they turn out. The instructors are very helpful. When I have a question, they are right thereto answer it. If I need something, some kind of guidance,they show me and then they let me do it. One of the reasons I chose to take Autobodyhere at Surry was that I have always wanted to paint cars give those custom paint jobs. That's one of the reasons I took it. This right here is my truck that I have beenworking on restoring it. I want to give it an aftermarket paint jobsomething that would look nice. The instructors here are helpful and knowledgeableon anything they need. They know their thing so whenever you needhelp or when you are doing something they will come and help you out. You get it done the right way. This is really exciting. You are always excited when you start somethingto get it done. I grew up as a tomboy working on a farm helpingmy paw. That’s probably what got me into likingand working on cars. I love cars. I like working in Autobody because I likeworking with my hands and working on cars and helping people. I am just going around helping people likeNancy over here. I help her a lot. The other day I helped her take an exhaustoff. I helped David sand his truck a little bit,and I been working on the school’s hotrod. I painted the bottom of it. I was just going to take automotive, but nowI have decided to take Autobody because most of these dealerships are going to have Autobodyand Automotive so that’s a double whammy. When I get out of college, graduate, I’dlike to work at a dealership. I hope to get a job at a Jeep dealership becauseI love Jeeps. Autobody professionals make about $39,000per year or more based on experience. Extremely successful Autobody shop ownerscan make in the neighborhood $60,000 to $100,000 in the Piedmont Triad area. High school juniors and seniors can take Autobodyclasses tuition-free through the Career & College Promise dual enrollment program. For more information, go to www. Surry. Edu. You can also follow the program on Facebook@SurryAutobody.


Brake Check in New Jersey

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in New Jersey. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in New Jersey. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

Wheel Alignment

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in New Jersey is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

Secrets of the Auto Body Shop

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in New Jersey are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Brake Repair Cost

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in New Jersey is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

Mechanic's Liens - Friday's Free Form - Notice of Intent to Lien - General Contractor

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

>> I'm Chad.

I'm a second-year student here at DCTC.

I've been an apprentice at ABRA inBloomington for just about a year, now.

Doing some frame damage,here, repair on a 2005 Ford.

>> Focus.

>> Focus.

Three door, got hit here,and this here was the main impact.

We've already cut the reinforcementand impact bar off.

Now, we're going to be pulling onthis frame here, to get it straight, using the three-dimensionalmeasurement system to make sure that everything else is inline where it should be.

>> I'm Gerry Rainford.

I'm a second-year instructor here,at Dakota County Technical College.

Chad's a typical second-year student, wherewe get into different levels of repair needs, from just simple door repair to, well, you cansee here, is a full unibody reconstruction.

Mechanical aspects, as well.

Getting into the air conditioning andother mechanical systems on the vehicle.

Suspension, driveline.

This is kind of the way that once we havethe vehicle anchored on our frame rack.

We come through and we can actually do pull out.

We're going to be doing a light pull,this morning on the unibody structure.

We're going to see if we can't repair the rails.

Typically, when they're kinked to thispoint, we would do a replacement procedure.

But we're going to see ifwe can't repair them, today.

So, we'll just kind of talk as we go through it.

And we'll see if we can getthe rails to come out.

So, Chad, please take over from here.

>> All right.

I'm going to be using these towers, here, thatare capable of pulling 10,000 pounds apiece.

Try to get this mash come outon this left frame rail, here.

>> So, once again.

Keep pulling.

We're going to be pulling at a constantlevel that's going to be straight out, to try to replace the height, thelength, and width of the rail.

So, we're going to keep the directionstraight and at a straight pulling distance.

>> And all I'm doing here, now, is justwatching as I'm pulling, going slowly to find out how the metal's going to react.

Everything reacts different,not any accident is the same.

Everything needs to be takenon with a different viewpoint.

What I'm going to do now, isjust hit this metal, here, to try to relieve some of this stress.

[ Hammering Sound ] And always while you're pulling,what you're going to want to do is check your anchoring points, again, tomake sure that the car is not going anywhere.

Make sure all your chainsand clamps are still tight.

As you'll notice, I'm staying above,not standing behind these chains, just in case anything would happen to let go.

[ Hammering Sound ] >> Let's work the backside of the railthrough here a little bit, as well.

[ Hammering Sound ] [inaudible] target.

One of the things we don't want to do, is we don't want to do additionaldamage as we're pulling.

Looks like we're pulling morefrom the bottom of the rail.

>> Yeah.

>> Than we are from the top.

So, at this point in time, I think we shouldstop, rehook, and grab a hold of the top of the clamp support and pullmore on the top of this rail.

>> All right.

Both these dozers here are run by the same pump.

So, as I pull it's going to pull them equally.

>> Okay.

Let's get some pressure on there.

[ Inaudible Comments ] [ Hammering Sound ] >> Just trying to relieve this stress.

Move the metal where I want it.

>> So, let's get a couple ofhits with this on the backside.

[ Hammering Sound ] Right now, we're concernedwith overpulling on it.

And so, I think we're going to stop.

And we're going to regrab ontothe rail at a different location.

Once you've overpulled and it distortsthe rail, then we've got an issue.

>> We're going to cut this outsideof this rail, here off, this cap.

Just a piece of the sheet seal,here, out of high strength steel.

We're going to pull this out here, sothat way we can get inside here, too, and make proper welds and getthis metal straight, again.

I'm just going to be countered along,drill out these spot welds, here.

And then, cut it here at the seam.

I'll run a line, section it out.

>> Why don't you show them how we know how farwe need to pull by using the measuring system? Then, to explain the measuringsystem, real quick? >> All right.

As we pull out on this stuff here, toget this rail out to where it should be, these targets here measure with this beamunderneath the vehicle, measures the vehicle at all kinds of different points.

Four in the middle of the vehicle, twoat the rear of the vehicle, and then, these here in the front closest to the damage.

This vehicle, this chart here for thevehicle is specific for this vehicle.

What this does here, is it hangs targets fromthe vehicle at specific manufacturing locations.

It measures the vehicle throughout there.

You can tell that our centersection here, is good.

And the back of the vehicle is good.

But up here, we're dealing with offmeasurements on the front end from the impact.

>> We're going to take and when we getthe rails pulled back into a location by the manufacturer's specifications, we'lltake, we'll hammer and dolly all this straight.

And we'll take, we've got new components.

We've got a new reinforcement barthat we'll be welding into place, to replace the structure of the vehicle.

But we'll come through, replace the.

You want to come around over here.

You can see that the radiator condenserhas been damaged in this accident.

And it's completely, we've lost all the Freon.

So, we'll be doing an R and Rprocedure on the condenser assembly.

Then, we're going to evac andrecharge the air conditioning system.

And then, move forward with the restof the mechanical repairs at this time.

In some situations, when you getcomposite intake manifolds, like this, components can come back and dodamage to the intake manifolds, starters, alternators, AC compressors.

We have additional damage deeper in the vehicle.

And this one, we've simplygot a condenser to replace.

What's so, how long will ittake you to do this repair? >> This repair here, will take me probablyabout two weeks to finish, to complete.

Done quite a bit already.

Already had all my parts ordered.

Those have already been checkedin and identified, and made sure that they are the rightparts, so I'm not scrambling at the end of the project to find the correct parts.

I'd say about two weeks; two to three weekswould be a good timeline for this vehicle.

>> Well, thank you, Chad.

I appreciate it, taking your time withthe students and this is what we do here at Dakota County Technical College.

It's a two-year program.

We try to get you ready with the latesttechnology and the latest equipment to make sure that they're ready for the industry.

And so, they can be productive and profitablein today's unibody reconstruction world.

Thanks, very much.

Auto body (Collision Repair and Refinishing)

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In New Jersey Should Help You With What Car Needs Exactly?

Custom Tires

A car is a very complex piece of machinery. Each individual part is vigorously tested before it ever goes into production models and, like a chain, relies upon every other part in order for the vehicle to function. One poorly built aspect can cause serious malfunctions leading to costly repairs, or worse, an accident.

Even something as simple as the glues used to hold a tire tread to the rest of the tire is an integral part of a car or truck. Just ask Firestone. That exact issue resulted in a costly recall of thousands of tires, legal recourse, as well as over 500 injuries and 148 deaths. All of which could have been prevented with only a little bit of testing. Be wary of new designs rushed into mass production.

Often a seemingly superficial part to a vehicle actually provides a significant amount of safety. Everyone knows a windshield protects the driver and passenger from wind and debris. Most also know that they are also designed with a thin film that prevents them shattering upon impact. What most people don't know is that the windshield provides over half of the structural support for the car during an impact. The windshield combined with the frame of the car makes it structurally safer than a car without one. Cracks in a windshield can greatly reduce their protective power, as well as obstruct the driver's view which is even more dangerous.

Replacing or repairing cracks and chips in a windshield should be done by trained professional at a certified and insured auto glass or body shop. Avoid independent installers and people who operate only out of their truck. The adhesive used dries in about an hour, so if any body shops quote you a turn around time less than that, they are either lying or don't know what they are doing.

Also, it is a good idea to know a little bit about the glass windshields they will be installing. There are three aftermarket windshields that exceed OEM and DOT specs, they are P.P.G., L.O.F. and Plinkington.

Other suitable windshields are made by the car factory. Ford's factory glass is called Carlite, and Chrysler's is Safeguard. Expect to pay more money for factory glass. A good auto glass installer will sand all the rust around the windshield after it is removed, and then prime and paint it before installing the new windshield. It is best to go with body shops that have been around for at least five years as they are more likely to be around to guarantee warranties and make repairs in the future. Many shops will also work with your insurance carrier to get you the best price on a windshield, sometimes completely paid for by the insurance company.

Body repair is another story and can become very expensive. Newer cars with plastic and fiberglass bodies are almost impossible to repair, the body panels are often much easier to just replace, and that can be accomplished by almost anyone with a wrench and screw driver. Repairing dents and rust on metal bodies can be time consuming as well as expensive. It also requires a matching paint job which is similarly expensive. If the dented or rusted panels can be removed it makes it much easier. Dents can be pounded back into shape. In addition to this, it is often just easier to work on and paint a detached piece. Some work can be done by the average Joe, but extensive body work should be done at an established body shop.

What Are Collision Services? How Do They Work?


Best Auto Body Shop in New Jersey