Best Auto Body Shop in New Jersey

If you’re looking for an auto body shop in New Jersey make sure you give Peotters Tire & Auto a call as the New Jersey areas premier tire and brake shop. Today’s vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop in New Jersey to be aware of the different materials and techniques used for repairing them.

Auto body shops like Peotter’s Tire and Auto and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills.

A good, eco-friendly auto body shop in New Jersey will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

My name's Dennis Nottingham, I'm themanager here at the Progressive Auto Group Collision Center and today we are going to berepairing a two thousand eleven Chevy Malibu Here at the body shop we have over fourhundred years of combined experience.

All of our technicians are ASE and I-Car certified.

What that means for you is a safe timely quality repair.

We are repairing the right frontsuspension and engine cradle.

After this the vehicle gets a four wheel alignment.

Next the body work is performed with theappropriate fillers then on to the paint department.

As you can see all the moldings and handles are removed the vehicle is masked off and the final sanding is complete.

Once in the in the paint booth the vehicle is prepped repair panels are then sealed three coats of base coat are applied followed by the clear coat once the vehicle has been baked for at ahundred and eighty degrees goes back to reassembly lastly over to the detail departmentwhere the final touches take place and the vehicle is cleaned inside and out If you would like a free estimate please give us a call we do work on all makes and models andthanks for watching the video.

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part.

Used Truck Tires

Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.

Who Really IS the Best Auto Body Shop in New Jersey ?

Tire Warehouse Near Me

>> I'm Chad.

I'm a second-year student here at DCTC.

I've been an apprentice at ABRA inBloomington for just about a year, now.

Doing some frame damage,here, repair on a 2005 Ford.

>> Focus.

>> Focus.

Three door, got hit here,and this here was the main impact.

We've already cut the reinforcementand impact bar off.

Now, we're going to be pulling onthis frame here, to get it straight, using the three-dimensionalmeasurement system to make sure that everything else is inline where it should be.

>> I'm Gerry Rainford.

I'm a second-year instructor here,at Dakota County Technical College.

Chad's a typical second-year student, wherewe get into different levels of repair needs, from just simple door repair to, well, you cansee here, is a full unibody reconstruction.

Mechanical aspects, as well.

Getting into the air conditioning andother mechanical systems on the vehicle.

Suspension, driveline.

This is kind of the way that once we havethe vehicle anchored on our frame rack.

We come through and we can actually do pull out.

We're going to be doing a light pull,this morning on the unibody structure.

We're going to see if we can't repair the rails.

Typically, when they're kinked to thispoint, we would do a replacement procedure.

But we're going to see ifwe can't repair them, today.

So, we'll just kind of talk as we go through it.

And we'll see if we can getthe rails to come out.

So, Chad, please take over from here.

>> All right.

I'm going to be using these towers, here, thatare capable of pulling 10,000 pounds apiece.

Try to get this mash come outon this left frame rail, here.

>> So, once again.

Keep pulling.

We're going to be pulling at a constantlevel that's going to be straight out, to try to replace the height, thelength, and width of the rail.

So, we're going to keep the directionstraight and at a straight pulling distance.

>> And all I'm doing here, now, is justwatching as I'm pulling, going slowly to find out how the metal's going to react.

Everything reacts different,not any accident is the same.

Everything needs to be takenon with a different viewpoint.

What I'm going to do now, isjust hit this metal, here, to try to relieve some of this stress.

[ Hammering Sound ] And always while you're pulling,what you're going to want to do is check your anchoring points, again, tomake sure that the car is not going anywhere.

Make sure all your chainsand clamps are still tight.

As you'll notice, I'm staying above,not standing behind these chains, just in case anything would happen to let go.

[ Hammering Sound ] >> Let's work the backside of the railthrough here a little bit, as well.

[ Hammering Sound ] [inaudible] target.

One of the things we don't want to do, is we don't want to do additionaldamage as we're pulling.

Looks like we're pulling morefrom the bottom of the rail.

>> Yeah.

>> Than we are from the top.

So, at this point in time, I think we shouldstop, rehook, and grab a hold of the top of the clamp support and pullmore on the top of this rail.

>> All right.

Both these dozers here are run by the same pump.

So, as I pull it's going to pull them equally.

>> Okay.

Let's get some pressure on there.

[ Inaudible Comments ] [ Hammering Sound ] >> Just trying to relieve this stress.

Move the metal where I want it.

>> So, let's get a couple ofhits with this on the backside.

[ Hammering Sound ] Right now, we're concernedwith overpulling on it.

And so, I think we're going to stop.

And we're going to regrab ontothe rail at a different location.

Once you've overpulled and it distortsthe rail, then we've got an issue.

>> We're going to cut this outsideof this rail, here off, this cap.

Just a piece of the sheet seal,here, out of high strength steel.

We're going to pull this out here, sothat way we can get inside here, too, and make proper welds and getthis metal straight, again.

I'm just going to be countered along,drill out these spot welds, here.

And then, cut it here at the seam.

I'll run a line, section it out.

>> Why don't you show them how we know how farwe need to pull by using the measuring system? Then, to explain the measuringsystem, real quick? >> All right.

As we pull out on this stuff here, toget this rail out to where it should be, these targets here measure with this beamunderneath the vehicle, measures the vehicle at all kinds of different points.

Four in the middle of the vehicle, twoat the rear of the vehicle, and then, these here in the front closest to the damage.

This vehicle, this chart here for thevehicle is specific for this vehicle.

What this does here, is it hangs targets fromthe vehicle at specific manufacturing locations.

It measures the vehicle throughout there.

You can tell that our centersection here, is good.

And the back of the vehicle is good.

But up here, we're dealing with offmeasurements on the front end from the impact.

>> We're going to take and when we getthe rails pulled back into a location by the manufacturer's specifications, we'lltake, we'll hammer and dolly all this straight.

And we'll take, we've got new components.

We've got a new reinforcement barthat we'll be welding into place, to replace the structure of the vehicle.

But we'll come through, replace the.

You want to come around over here.

You can see that the radiator condenserhas been damaged in this accident.

And it's completely, we've lost all the Freon.

So, we'll be doing an R and Rprocedure on the condenser assembly.

Then, we're going to evac andrecharge the air conditioning system.

And then, move forward with the restof the mechanical repairs at this time.

In some situations, when you getcomposite intake manifolds, like this, components can come back and dodamage to the intake manifolds, starters, alternators, AC compressors.

We have additional damage deeper in the vehicle.

And this one, we've simplygot a condenser to replace.

What's so, how long will ittake you to do this repair? >> This repair here, will take me probablyabout two weeks to finish, to complete.

Done quite a bit already.

Already had all my parts ordered.

Those have already been checkedin and identified, and made sure that they are the rightparts, so I'm not scrambling at the end of the project to find the correct parts.

I'd say about two weeks; two to three weekswould be a good timeline for this vehicle.

>> Well, thank you, Chad.

I appreciate it, taking your time withthe students and this is what we do here at Dakota County Technical College.

It's a two-year program.

We try to get you ready with the latesttechnology and the latest equipment to make sure that they're ready for the industry.

And so, they can be productive and profitablein today's unibody reconstruction world.

Thanks, very much.

Auto Body Shops and Custom Work

Wild Country Tires

Today's vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop to be aware of the different materials and techniques used for repairing them.

Auto body shops and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills. A good, eco-friendly auto body shop will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part. Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.


Brake Check in New Jersey

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in New Jersey. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in New Jersey. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

Watch A Full Body Shop Repair In 90 Seconds

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in New Jersey is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

How to Find Auto Body Shops

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in New Jersey are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Used Truck Tires

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in New Jersey is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

Prevent Common Problems with Body Filler

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

People understandably get confused between wheel alignment and balancing. So what is wheel alignment? Wheel alignment is simply making sure that all four wheels are pointing in the right direction. During the course of your car's life it will have to make it over speed bumps, up and down curbs and across many pot holes! This can all affect the wheel alignment and if it is out by a few degrees it will cause uneven tyre wear. This means that your tyres are not correctly in contact with the road.Another issue that could occur is earlier and more frequent tyre changes than you would normally require, and annoyingly only a quarter of the tyre may even be worn. Four wheel alignment is usually carried out using laser technology. All four wheels have a laser fitted and a measuring board indicates the wheel alignment. If the wheel alignment is out it is then adjusted at this stage. The adjustments will be visible on by the laser showing the technician when to stop or exactly how much adjustment is required.Why is it important to have wheels balanced? When the tyres are fitted to the wheel they are not perfectly balanced. This means that if you had your new tyres fitted without the balancing in place you would experience a juddering sensation through the steering wheel. This can be uncomfortable and if the wheel balancing is a long way out the steering wheel will shake in your hands. This can obviously be quite dangerous and potentially lead to accidents! Therefore it is recommended that the wheels are balanced every time new car tyres are fitted.The wheel balancing is a process that is carried out by a machine. The tyre technician will fit the new tyre onto the wheel and then clamp it onto the machine. The balancing machine then spins the wheel around and then calculates the weight required to counterbalance where the wheel is out. The weight is then fitted to the exact spot on the wheel and is then rechecked to make sure the wheel is perfectly balanced. The weights are either stuck on or clamped onto the wheel. If the vehicle is fitted with alloy wheels then the weight will be stuck to the wheel. This avoids damaging the wheel. The stuck on weight is generally fitted to the inside of the wheel so the aesthetic appeal of the alloy wheel is not lost in the process.

Wheel Alignment and Tire Balancing: Why Are They Important?

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In New Jersey Should Help You With What Car Needs Exactly?

Wild Country Tires

When you think of auto body shops, the first thing that pops into your mind is usually a place where you bring your car to after you an accident that needs some sort of collision or damage repair done; you might also think that an auto body shop is a place where you would bring your car to for some minor touch up work for various scratches or dents that have mysterious migrated onto your car. Thinking these things is by no stretch wrong but another thing that auto body shops perform is custom car modifications.The realm of things that can fall into the category of custom automotive work are endless. Everything ranging from body kits to mufflers and even paint jobs can be perform by your local body shop providing they have the proper supplies and equipment for the job. As with all things, some auto body shops have a better reputation then others when it comes to do custom work. A good thing to keep in mind is the workload of the garage you are planning on visiting on any given time. If the body shop you are trying to use is full of customers, they might very well be able to do the work but the turn around time would be long. If the reputation of the shop is good enough then it is worth the wait and going through the hassle of making other plans while your car is being worked on.After you have decided on the type of work you would like to have done to your car, you should specifically ask one of the auto body shops you have in mind if they can perform the job. If you have a fancy car that requires special tools of mechanical knowledge then it might be out of the realm of possibility for certain garages. It is also well worth it to research the auto body work shop you are planning on visiting in terms of any complaints filed against them before you bring your car in. The best way to do this is by looking on the Internet for reports filed against the shop you are interested in.Before any custom work is done to your vehicle you should ask upfront for a clear cut estimate and to be telephoned if any extra work needs to be performed that is vital to the success of the original job request. If you have found a good garage, they would not do any extra work without your prior consent or agreement.

Watch A Full Body Shop Repair In 90 Seconds


Best Auto Body Shop in New Jersey