It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in Livingston. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.
What is the next step after your collision and you need an auto body shop?
Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.
Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in Livingston.
They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.
This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.
Auto Body Repair: Pull on a 2005 Ford Focus
Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.
Now here are some things to watch out for. a local auto body shop in Livingston is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.
Caster, Camber, Tow-In - Wheel Alignment
Replacement Parts in Auto Body Shops
Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in Livingston are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.
Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.
No Realignment? Talk to Your Auto Repair Team!
The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.
Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.
Using Bondo (Fillers) Instead of Replacing the Part
Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in Livingston is doing, they tell you, and this is what you are paying for then it is fine.
The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.
The Importance of Proper Wheel Alignment
All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!
Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.
Mountain biking is one of those sports that you have to be prepared for and in good shape. Since the terrains will be quite challenging and physically demanding, you have to think about various things to prepare.
The bicycles are specifically designed for road use and harsh terrains. Today's bicycles seem like something from the science fiction movie compared to the first one designed in the late 1800s. Among the first examples are the bikes modified for off-road travel of the expedition of soldiers from Missoula to Yellowstone, the USA in 1896.
Mountain bikes have different characteristics than normal bike variety. They use features to increase durability and obtain optimal performance in difficult terrains. These differences include tires, handlebar, smaller frame and better brakes. Pedals even differ among the mountain bike models and can be platform or clipless. This also means that they range in price as well as quality.
The travel alone can take days in the rough terrain and you will have to set camp or plan your stay in a nearby place. This means that you should pack appropriately and that you shouldn't start your travel without the certain things.
Help local community
You will be tempted to make stops at the famous brands on your travels. This includes restaurants, hotels and other big chains you already heard about. But one of the benefits of mountain biking is that you will come across a lot of local small businesses.
Buy fruits and vegetables from the local farmers, stay at the bed and breakfast and eat at diners. This is a fine way to help the smaller and local business community. Also, it may prove more quality than eating junk food or cheaper than bigger chains.
Plan the bike route
There are many attractive places for mountain biking, and some are even famous for it. However, that doesn’t mean that you should go without planning your route. It is a recreational activity and you will certainly enjoy nature, but consider setting up goals.
Additionally, that will help you to plan the rides based on the terrain type, weather conditions and elevation. Choose the trails that fit your stamina and preparedness the best, as well as what you want to achieve. Some people enjoy mountain biking purely for recreation, while others want to lose weight or train for more demanding rides.
Don’t forget insurance
Mountain biking is an extreme sport and can lead to injuries. Buy travel insurance so your possible medical costs are covered and in case your trip gets cancelled. Accidents happen and you can’t take a risk with your health or any unpredictable event.
There are various options for insurance and you can choose the one you consider the best for your mountain biking plan. However, don’t try to save money on important issues like buying appropriate insurance for yourself in case of injury, theft or delayed flights.
Snacks, meals and beverages while travelling
Eating the right foods is important every day, but when you are doing something physically and mentally demanding then you have to make sure you’re eating properly. Mountain biking requires appropriate energy for the travel and you can achieve that through food.
It’s important to stay hydrated at all times and a water bottle should be always by your side. Fruits like bananas and apples are important for vitamins and natural sugars. Make peanut butter sandwiches and take canned food with you, like tuna for the protein.
For example, squash bananas, apples in the bowl and add blueberries and Japanese BCAA amino acids. Mix all that with milk and add whole wheat cereals you left to soak in water overnight. This type of breakfast is not only healthy but will keep you sated until you make a break for a snack by the road.
Don’t litter the environment
One of the advantages of mountain biking is that you will have an opportunity to enjoy amazing landscapes and natural beauties. This connection with nature will also keep you in the wild for a couple of days and that means that you will have to take care of the garbage.
Bring garbage bags with you, use recyclable materials and don’t litter around. Don’t throw away your garbage in nature, but rather wait until you encounter a settlement or garbage bin. Respect the wildlife and don’t try to pet the dangerous animals or hurt them out of fear. If you plan to ride through the parts famous for its wildlife, travel in a group and make noise so the animals would get out of your way.
Check your bike
Before you start your journey, leave an emergency contact information in your passport and check your bike. You can also carry the emergency contact information in your wallet, and include the embassy number beside the friend or family member details.
You can take your bike to the bike shop for a more detailed check-up, but there are some things you should do on the spot. Drop your bike on the floor to see if anything is rattling or unscrewed. Test the breaks and tires to make sure that they’re working properly. Adjust the wheel and secure it tightly, as well as the headset.
If anything is not in order and you can’t fix it by yourself, it’s better to go back and seek professional help. The same applies if any damage occurs on the road. Don’t attempt to ride with the broken or unsecured bike since that can lead to serious injury.
Think about safety first and approach all your riding plans that way. Mountain biking is an exciting sport that certainly deserves the attention and popularity it gained. However, just like any sport, it takes prepared and responsible people to participate.
What to Look for in an Auto Body Shop
The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.
Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.
Your Auto Body Shop In Livingston Should Help You With What Car Needs Exactly?
- Hey this is Donnie Smith.
This lesson, we're gonnatalk about dent repair.
Now before we just jumpon this car and start repairing this dent, it'simportant for any repair job to wash it good withsoap and water to remove all the contaminants,the waxes and greases.
We've already done that,we used a power washer to clean the car and now we're using a wax and grease remover.
And this is just toassure that all the waxes and greases, silicones,things like Armor Alls that may have been sprayedaround the vehicle are removed, 'cause this will eliminatemany of the paint problems that arise during a repair process.
This will also save onsandpaper cause it won't be loading the sandpaperwith these contaminants.
Now we have the repair areaclean and we can begin repairs.
But before we do, we wanna take a look at the damage and seewhat's wrong with it, see where the indirectdamage is and direct damage, and determine what repairmethods we're gonna use to repair this damage.
Now when thinking aboutdamage, it's a good idea to think about water.
Because you know if somethinghits water it goes down, and when it goes down italso pushes a wave up.
So you've got the low areaand you've got the high area.
Think of damage the sameway, because any time there's a dent there's gonna be a low and there's gonna be a high.
So whenever you look at thisdamage, you can see that the center part of the dent isof course the direct damage, but then if you look up here on the top, you can see the crown, oreyebrow some people call it.
And you can see that that is pushed up.
That whole top of the fenderis actually pushed up.
So if you tried justto pull out on the low, or push down on the highthat's not gonna work.
You've got to roll themetal, you've gotta push down on that high while you'repushing out on the low.
Now, when you go todetermining what repair method you're gonna use, you mayhave some different types of tools, you may havesome high dollar tools, a stud welder gun, otherdent repair systems.
Where really what you wanna think of is what is the easiest method? If it's a hammer and dolly,you have access to both sides, then use a hammer and dolly.
Just because you've got thehighest piece of equipment does not mean you haveto use it every time.
Now on this particularrepair, if you drop the liner, you are able to get to the back side.
So if you can get to the back side, this would definitely be acandidate for hammer and dolly.
Feeling back there to see ifthere's room to get a dolly, which I determined that there is.
Another thing to remember isthat whenever you're repairing a dent to reverse what happened.
You wanna work from the outside in.
First in, last out.
So whatever happened first in an accident, that's the last thing you wanna repair.
Also remember whenworking with thin metal, it's thin, and you may be able to move some of this with yourhand some of the times.
Doesn't work every time, butI'm gonna reach back there and keeping that in mind that I'm gonna push down on that high,out on the low area, use my hands to rough this out.
Now this ain't gonna be perfect, it's just to rough out the damage, to get the majority of the damage out.
I can see that there arestill some highs and lows, I can feel 'em.
I know it's hard to see on the video, and even if you're doingthis yourself it may be hard to see this sometimes, butI've got a trick that'll help you locate the lows.
If you get a block withsome 80 grit on it, you can cross sand the damaged area, and what this'll do is that the highs will immediately go to metal, of course, 'cause they're high,but the lows, you'll see it doesn't sand it at all, andthis will identify the lows.
Now you can see the twolow areas very easy.
Now using the dolly, I'mgoing to reach behind this panel with the dollyand I'm gonna push out on those low areas.
Also, while I'm pushing outI'm gonna have to remember where those high areas areso I can tap in on those.
Remember, we always wannawork in multiple directions.
Whatever tool you're using, just remember to push out on the lowsand in on the highs.
Also, when using adolly, there's different dollies, different shapes.
You want the shape of thedolly to fit the contour of the part you're working on.
If this dolly was completelyflat it wouldn't work well with this repair.
Okay, now I am working on getting my dolly located on the back of themetal where I want it to go.
It may take a little bitof time to get it exactly where you want it, but I wantit right on those low areas, so that I can raise the low areas out.
Also while I'm raising lowareas out, while I'm pushing on them with the dolly, I wannatap down on the high areas.
This will allow the lowareas to come out while the high areas are tapped in.
This is called the Hammeroff Dolly technique, because I'm not actuallyhammering on the dolly.
The dolly is pushing out on the low, the hammer's pushing in on the highs.
There is also a Hammer on Dolly, and that's where youare hitting the dolly.
Any time you hammer on dollythat stretches the metal.
You wanna save that for your final stages, until you get the metalcloser to where you want it.
Then you can do some hammer on dolly for your final straightening.
So I'm gonna do a little bitmore metal straightening, and then I'm gonna use the block sander with some 80 grit on it tocontinue blocking that out to identify my highs and lows and see how the progress is coming.
Now whenever you're blocksanding with 80 grit to identify highs andlows, it's always important to cross sand.
By sanding in just onedirection, you're not gonna find all the highs and lows.
And this goes for if you're doing this to identify highs and lows,or block sanding body filler.
Cross sanding always levels much better.
Now we're using this sander,and this basically takes the place of what we usedto use with thicker metals, which is a body file.
However a body file will actually shave the top layer of the metalwhich would help level it.
We don't wanna do thatwith thinner metals.
We wanna use methods thatdoes not remove any metal.
So any method that you canuse that does not remove metal is always gonna be a better choice with these thinner metals.
Now I'm feeling out thedamage with my hand, just seeing what all highsand lows that I feel.
A little tip for feeling damage, because you'll have to do that often, is to use the flat of your hand.
Often I see fingertipsused, but that is not gonna catch the highs and lows,you're gonna miss 'em.
So always use the flatof your hand to be able to feel the damage.
Another trick that sometechnicians use is to use a rag, they claim that they can feel it better, it kinda eliminatesthe different textures.
You put a rag over yourhand and go over the damage and see if you can feelthe highs and lows better.
Try both ways, whichever works best is the method for you to use.
Now I feel a little bit ofhigh, so here I identified a high, so I'm just gonna tap that down with the pick side of the hammer.
I'm just basicallylowering that high area.
Now I'm going to re-blockit, re-sand it with this 80 grit to make sure thatit did remove the high area.
I feel of it, and I feelthat that feels good.
It's not perfect, butwith these thin metals, if you try to get 'em just perfect, try to metal finish 'emlike they did older metals, you're gonna weaken and thin the metal.
You wanna get it within 1/4 of an inch.
Anywhere between 1/8 and 1/4 is what most body fillersuppliers recommend.
However, you don't wannaexceed 1/4 of an inch, that's maximum after sanded.
You don't wanna exceed that amount.
This dent is well underthat, it's probably within 1/8 of an inch.
I'm noticing there's stilla little bit of a crease down here so I need to work that out.
I'm gonna get a hammer and dolly in there, I'm gonna raise in on the low area and I'm gonna tap this crease area in so that we can roll this metal back to where it's supposed to be.
As I'm pushing out with the dolly, I'm tapping in on that high area.
Now I'm being real careful herenot to hit the bumper cover.
It'd've been a better idea if I went ahead and dropped the bumper cover.
I'll probably be blending into that.
Another trick you can do is put a couple layers of masking tape.
I should've did that, Ishould've put masking tape or went ahead and dropped the bumper.
Because the last thingyou wanna do is sand into an adjacent panel,especially if it's not one that you're blending and cause damage that you have to repair.
I'm still having problemswith the low area right here, so I'm working on that.
Now the problem with this area, it's a little harder to get to'cause there's a brace there.
I'm following the same techniques, I'm gonna push out on that low area and I'm tapping around the high areas.
When I hammer on dollyyou can hear that ping, it makes a different sound.
You can hammer on dolly someto help remove that damage, but again remember thatthat stretches the metal and try to reduce theamount that you do that.
Little bit of a high, I knocked that down.
Okay, I'm gonna use my block with 80 grit to sand the damaged area some more to see if I got thedamage worked out enough to apply the body filler.
And I sand it and I feelof it, and there's still too much of a low there.
So I'm going to need to goback in there one more time and use the dolly and hammer.
I'm going to use the pickbecause there's a high here.
I'm pushing out on thatlow and I'm going to hammer on dolly a little bit,and sand it one more time to see if that has it.
And that's what it takes, itjust takes doing a little bit, feeling of it, checking your progress until you have thedamage where you want it.
We got the metal straightenedwithin 1/4 of an inch, really within 1/8, but 1/4 after sanded is the maximum amount of filler that most body filler manufacturers recommend.
No more than 1/4 of an inch.
That's the maximum amount.
I know 3M, Evercoat, they all have that on their technical data sheets.
So anything more than 1/4 of an inch you really need tostraighten it more than that.
You need to get it straighter.
Again, with these thinnermetals you don't wanna try to work it and work it,because you're gonna work-harden the metal.
It'll become work-hardened, thin, brittle, it may even crack on you.
It's almost impossible toget these thinner metals to do the metal finishingtechniques like they used to do where they'd work the metaland file it down and get it just perfect, prime it.
Now there is one exceptionto that, and that's PDR.
Paintless Dent Repair.
That's a total different set of techniques than we went over in this video.
This video is straightening metal like a body shop would perform.
Again, remember dependingon the extent of damage, like a fender, that wouldreally go into consideration, do we wanna repair that or replace it? Now on 1/4 panel, thosepanels usually cost more.
And also, it's a weld onpanel, so it's gonna take a lot of labor to replace it.
So you can have a lotmore damage in 1/4 panel than you would a fender,and still repair it.
Many times in body shops and dealerships, if there's even a couple ofhours of damage on fenders, they just go ahead and replace them, which is R and R, Remove and Replace.
Anyway, I hope you learnedsomething this lesson.
Thanks for watching, we'llsee you in the next lesson.