Auto Body Shop Summit, NJ – What Can they do for You?
If you experienced some frame damage to your car, you’ll need some repair and Peotter’s Tire & Auto is just the place to get it taken care of.
What are the three questions should ask a body shop before they consider dropping their car off for repairs?
Well what’s important is that the repair shop actually be qualified to fix that particular vehicle.
Today modern cars require specialized training and equipment to be able to perform repairs to the manufacturer’s standards.
So, glue joints and rivets.
They’re actually repaired like aircraft today.
This is important because this maintains the structural integrity the manufacturer designed for a repair situation.
My name's Dennis Nottingham, I'm themanager here at the Progressive Auto Group Collision Center and today we are going to berepairing a two thousand eleven Chevy Malibu Here at the body shop we have over fourhundred years of combined experience.
All of our technicians are ASE and I-Car certified.
What that means for you is a safe timely quality repair.
We are repairing the right frontsuspension and engine cradle.
After this the vehicle gets a four wheel alignment.
Next the body work is performed with theappropriate fillers then on to the paint department.
As you can see all the moldings and handles are removed the vehicle is masked off and the final sanding is complete.
Once in the in the paint booth the vehicle is prepped repair panels are then sealed three coats of base coat are applied followed by the clear coat once the vehicle has been baked for at ahundred and eighty degrees goes back to reassembly lastly over to the detail departmentwhere the final touches take place and the vehicle is cleaned inside and out If you would like a free estimate please give us a call we do work on all makes and models andthanks for watching the video.
Like this fixture frame bench here that utilizes actual jigs to support the vehicle across its entire platform and place factory components precisely where the manufacturer has designated.
These systems are different than generic systems that simply are reverse engineered and don’t have jig and holding capacity.
Shops that aren’t trained and equipped to properly perform a repair utilizing generic equipment or generic procedures can’t restore the vehicle to the manufacturer’s standards and that doesn’t necessarily maintain the safety rating designed for the vehicle.
You potentially jeopardize the collision energy management system.
The vehicle might not perform the same in a future collision and you could possibly be more injured than you would if the car doesn’t perform as the manufacturer intended.
The second question a consumer should ask is “Where does the body shop’s loyalty lie?”
Is it an independent repair center that relies on satisfied customers to drive business through their door and therefore fixes vehicles correctly? Or is the body shop on the insurance company’s “preferred network?”
Those body shops rely on the insurance referrals and when those body shops utilize cheap, imitation, and savage parts utilize the quickest possible repair times and keep costs as low as possible that generates the next referral.
But that’s a recipe for shortcuts.
The third question, Paul, is “Can the repair shop make this process convenient for me?”
Most consumers today want convenience and ease.
Repair shops that are high-quality repair shops are going to put their customers’ interests first & do everything they can to have a satisfied customer.
That includes scheduling a rental car, scheduling a tow engaging in conversations with the insurance company and making sure the vehicle is fixed right for the consumer.
Today's vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop to be aware of the different materials and techniques used for repairing them.
Auto body shops and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.
When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills. A good, eco-friendly auto body shop will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.
The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part. Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.
Working with Plastics
The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.
It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.
Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.
The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.
Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.
Cleaning and Prep
Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.
Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.
This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.
Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.