Best Auto Body Shop in New Jersey

If you’re looking for an auto body shop in New Jersey make sure you give Peotters Tire & Auto a call as the New Jersey areas premier tire and brake shop. Today’s vehicles are made with many different types of fuel-saving materials like lightweight alloys and plastics. It is important for an auto body shop in New Jersey to be aware of the different materials and techniques used for repairing them.

Auto body shops like Peotter’s Tire and Auto and collision repair services refer to manuals for instructions repairing bumpers. The different material types require various finish materials, removal and installation procedures.

Bumper Repairs

When a plastic bumper is cracked or has a small hole it can be repaired to look as good as new. Replacing the bumper is wasteful and it creates unnecessary debris for our landfills.

A good, eco-friendly auto body shop in New Jersey will only recommend replacing the bumper if the damage is severe enough that repair time would be considered unreasonable and quality of results would be unsatisfactory.

My name's Dennis Nottingham, I'm themanager here at the Progressive Auto Group Collision Center and today we are going to berepairing a two thousand eleven Chevy Malibu Here at the body shop we have over fourhundred years of combined experience.

All of our technicians are ASE and I-Car certified.

What that means for you is a safe timely quality repair.

We are repairing the right frontsuspension and engine cradle.

After this the vehicle gets a four wheel alignment.

Next the body work is performed with theappropriate fillers then on to the paint department.

As you can see all the moldings and handles are removed the vehicle is masked off and the final sanding is complete.

Once in the in the paint booth the vehicle is prepped repair panels are then sealed three coats of base coat are applied followed by the clear coat once the vehicle has been baked for at ahundred and eighty degrees goes back to reassembly lastly over to the detail departmentwhere the final touches take place and the vehicle is cleaned inside and out If you would like a free estimate please give us a call we do work on all makes and models andthanks for watching the video.

The cost of repairing small abrasions, cracks and holes in plastic bumpers is often much cheaper than replacing the part.

Car Repair Loans

Of course, many collision repair technicians would rather replace the part and charge a fee for their labor plus mark-up on the price of the part because they lack in cosmetic repair skills and it is easier to warranty the work.

Working with Plastics

The first step to repairing plastic bumpers is to identify the material in order to choose the method of repair. Auto body shops use ISO codes on the parts to identify the various families of plastics. They cross-reference the codes with charts from the suppliers or by accessing reference materials on the internet.

It is important that the collision repair technician determine the type of plastic they are working with so they know the proper welding procedure to use to avoid damage to the part.

Some plastics can be welded with an airless welder or hot-air welder; others require a hot glue type of procedure. Tests must be performed and welding procedures have to be done correctly to avoid adhesion failure. Some bumpers will melt with a slight color change and they will remain tacky in the area where they have melted.

Adhesive Repairs

The bumper repair technician must identify the type of plastic they are working with in order to be successful with adhesive repairs. Failure to properly identify the plastic results in adhesion-related problems.

Flexibility

Some repair materials are based on flexible and rigid plastics. Using the wrong material can cause cracking when the part is flexed or it may not provide the correct strength for the repair area.

Cleaning and Prep

Proper cleaning and prep is critical for proper adhesion and finish. Whether the technician is repairing or replacing the bumper, the part will need to be cleaned. The bumper being repaired is likely to be dirty from the road; the new replacement part can have contamination on it from the manufacturing process.

Auto body repair professionals should use a low-VOC surface cleaner or a special plastics parts cleaner to help prevent solvents from going too deep into the plastic. If solvents are too harsh, they go deep into the plastic and cause adhesion problems after repairs are done.

This is an overview of the process of working with plastics. Time is money in the auto body industry; therefore, many collision repair technicians choose to replace rather than repair plastic bumpers and other parts.

Technology allows us to repair many items that are often replaced. As resources become scarce and landfills become over-full, we really should consider repairing rather than replacing when possible.

Who Really IS the Best Auto Body Shop in New Jersey ?

Auto Places Near Me

What is a wheel alignment? How does it effect handling and tire wear? When should I do an alignment? What causes alignments to go out? How would I know if my alignment is out?  A wheel alignment is nothing more than setting the angle of the hub/wheel so it tracks in the right direction. Most vehicles have four-wheel alignments, meaning each of the four wheels is separately aligned.  Your basic alignment consists of three angles: camber, caster  and toe-in. Camber is the tilt of the tire when viewed from the front of the car. Positive camber means the top of the tire is tilted away from the car. Negative camber means the top is tilted in. Camber has a lot to do with cornering performance. Too much negative camber will wear the inside of the tires prematurely. Too much positive camber will wear the outside tread. Caster is the inclination of the front spindle. Picture the angle of the forks on a bike top to bottom. When the caster is out, it creates a pull or wandering condition and sometimes a slow responding steering wheel. Toe-in is measured in inches or degrees. Viewing from the front of the car, it is the difference between the front and rear center-line of the tire. Toe-in means the fronts of the tires are closer together. Toe-out means, the fronts of the tires are farther apart. Toe-in or out has the most effect on tire wear. There is a lot more to suspension alignment, especially if you push your vehicle on the track. The modifications you make on your suspension are just the beginning. Once you start down this road you will be concerned with things like bump steer, weighting (vertical load), preloading, tire traction versus tire load, and more. Now you're thinking under-steer, over-steer, tire compound, sway bar design, and other topics that can be covered in a later article. For now, just remember to have your vehicle aligned every 10,000 to 12,000 miles in normal driving conditions.If you accidentally hit a curb, or drive through a nasty pothole or other road obstruction, that would be a cue to have your car's alignment checked more often. Proper alignment is good for your car. It will save unnecessary wear on your tires. It will ensure that your vehicle is giving you the handling the factory designed the car to have. And, most importantly, a properly aligned car is safer and more fun to drive.   

Tips on Why Wheel Alignment Is Important

Auto Body Collision Repair Near Me

Before you try to run out and find auto body shops near you, take a moment to read through this article and consider including some of my personal experience as a mechanic into your own personal deliberation about what constitutes the best auto body shops in business. When you break things down, there are really two types of garages in business: good ones and bad ones. The best place to start when trying to scope out a potential body shop is the owner. In bad auto body garages the owner usually instructs the employees to give the impression that your car is in worse shape then you think, or that something is broken and needs to be fixed right away. In a legitimate auto body garage, the owner is more concerned with forging a long standing relationship with you and getting your repeat business rather then just ripping you off and potentially never seeing you again.

The reason why most owners are concerned with ripping people off, especially in a body shop, is because the only two reasons cars ever go in there is for repairs on collision damage or for custom work; this means that the owners of the shop realistically do not see the owners of vehicles too often and do not see the value in repeat business, they would rather try to squeeze every dime out of your while you are there.

The best auto and body shop you can ever find is where the owner looks to develop long term relationships with their clients. While it is true they can potentially never see a newer customer again, these owners are smart and do the best work possible not only to help you out, but to impress you and have you refer your friends and family to him or her. These owners are less interesting in gouging your wallet and more interested in establishing a reputation in their local community for outstanding work and service. These types of people see the value in what it means to be a true professional and are more successful then their more selfish friends in the business.

The best way you figure out which owners are the good or bad guys is either by your own direct experience or the experience of others. You should not be afraid to talk to the auto body shop manager directly and begin to get a feeling for what he is about. After a short conversation and carefully studying his body movement and language, the first impression you get is often the right one.


Brake Check in New Jersey

It happens to all of us at one point in time. We get into an automobile collision and need the best auto body shop in New Jersey. Hopefully, it is not too bad and we are not seriously injured. But usually the car does not fare as well and comes away with significant damage.

What is the next step after your collision and you need an auto body shop?

Likely, after informing the insurance company you take your vehicle to one of their “approved” vendors.

Here is what happens next. You tell the insurance company what company you choose. By this time they have already taken phones of the car and know how extensive the damage is. If you need an expert to take a look, make sure you go to a repair shop in New Jersey. 

They have a computer system that gives them a printed estimate stating what the replacement parts and labor will be based upon a set hourly rate.

This statement is given to the body shop. It comes with a break down of what the labor and parts “should” be and the company has to usually be able to totally fix the car for that price.

How To Straighten Metal On Car Parts

Keep in mind that what is printed out represents the best case scenario and doesn’t allow for items on the car that was missed or problems that come up.

Now here are some things to watch out for. a local auto body shop in New Jersey is operating under very, very thin margins and the incentive to “cut corners” is huge. Getting an extra $300 off a job can really add up over the course of the month when you are talking about doing at least 3-5 vehicles every week.

How to Find Auto Body Shops

Replacement Parts in Auto Body Shops

Make sure the parts being used on your car are OEM parts. These are replacement auto body parts in New Jersey are sent directly from the car manufacturers and are designed with the same specs as the vehicle came with.

Tire King

Aftermarket parts can be significantly cheaper yet are not the same quality and make not hold up the same in the event of another accident.

No Realignment? Talk to Your Auto Repair Team!

The frame is usually somewhat bent when a car goes through an accident of any kind. It needs to be properly realigned. You need a serious all hands on deck auto body shop to take care of you here.

Unfortunately, because the money made off one car can be very little the propensity to skip this step is very high. Later down the road this will cause your car to not drive straight but at a tilt and your tires will wear prematurely. So if you need to brush up on some tire repair, ask your mechanic straight away.

Using Bondo (Fillers) Instead of Replacing the Part

Filling any damage in with bondo is not bad in itself. If you know what the auto body shop in New Jersey is doing, they tell you, and this is what you are paying for then it is fine.

The problem comes in when you think you are getting a vehicle back that is 99.9% the same as before it was wrecked and it is not. Filling a damaged part in with filler rather than replacing the expensive part is a common tactic and you want to make sure it is not done on your vehicle.

What to Look for in an Auto Body Shop

All damaged parts should be replaced unless you are paying a lower price for the car to just be fixed (in the case you want the cheapest price and do not care about having a car exactly the same as before). Again, you should really speak to your best auto body shop nearest you!

Keep in mind that most auto body repair shops are honest and are surviving in a tough industry.

Without knowing what to look for, choosing a quality auto body shop is tough. It's important to select the right auto shop to ensure the vehicle is fixed correctly the first time. It's also the best way to make sure the shop is honest and reliable. There are many important features of a good shop, including an experienced staff and certifications. It can also help to read customer reviews before making a selection.A Certified ShopA good body shop is certified by the largest auto organization. Facilities that gain the approval of the organization have proven their abilities as certification is often a lengthy process. To become approved, an auto shop must demonstrate it has the latest equipment, qualified technicians and a proper facility. It must also show it offers above average training to its employees. Larger associations always collect feedback from prior customers as well before issuing an approval. Auto shops can also receive certification from parts manufacturers and organizations like Autobody Alliance, which requires the shop to meet certain qualifications.Qualified and Experienced StaffA good auto body shop has qualified staff with a number of certifications. Certification from ASE (Automotive Service Excellence) is especially important. ASE is a non-profit organization that offers certifications to automobile technicians that show proficiency in their trade. Technicians may also have certification from car manufacturers like GM, Chrysler, Toyota and Nissan, showing their knowledge and experience dealing with particular car brands. Some auto technicians also receive aftermarket training from Bendix, Moog, or NAPA. Most training requires a great deal of knowledge and experience and demonstrates a technician is a professional in their field.Positive Customer ReviewsWhen possible, former clients should be consulted about their experience with the shop. Some resources to find reviews are online, making it easy to decide if a body shop has good feedback from the public. Reviews should mention that the vehicle was fixed properly the first time and work was completed in a timely fashion. Positive reviews should also discuss whether a warranty was offered by the body shop and if the facility was clean and orderly. A facility that has the approval of a large automobile association has shown a history of positive feedback from customers, although it's always a good idea to check into a shop as much as possible.Accepts All InsuranceAnother important aspect of a good body shop is its acceptance of all forms on insurance. An auto body shop that accepts all insurance providers demonstrates it has experience working with insurance companies to settle claims quickly. A shop that is hesitant to accept major insurance providers is a red flag that something may be wrong. This is also a matter of convenience and makes it easier for the vehicle owner to select a shop they feel comfortable with.Selecting the right auto body shop requires a bit of patience and consideration. For example, choosing the first shop available can be a disaster if the employees aren't trained properly. A good auto shop is clean and up-to-date with a friendly and knowledgeable staff. The shop should have positive reviews and a range of certifications for both the facility and technicians. It should also accept all forms of insurance, making repairs easy and convenient.

How to Spot a Scam Auto Body Shop

The insurance companies nickel and dime them at every turn and they are made to give them at time ridiculous discounts to get any business. That’s why having an auto body shop in your corner can’t be stressed enough.

Nevertheless, all an auto body shop should be on is your side and corners should not be cut at your expense and being watchful is just a smart way to go.

Your Auto Body Shop In New Jersey Should Help You With What Car Needs Exactly?

Truck Tires Near Me

What Is Caster - Camber - Tow-in - Wheel AlignmentFirst for those who do not understand caster, camber, and tow-in let me explain. Caster is how the wheel is in relation to a vertical king pin or ball joints. It can be true vertical or -o- degree, positive, or negative. Example: the front wheel of a bicycle has positive caster. Note the wheel extends forward from the turning axis. Therefore allowing the steering to return straight when you remove your hands from the handle bars. A vehicle with positive caster will do the same. This adjustment is for handling or how it drives and requires caster - camber gauge for adjustment as well as certain hand wrenches.Camber denotes the position of the wheel to the vehicle, such as in at the top and out at the bottom (negative), or out at top and in at the bottom (positive). The recommended setting can be negative 1 to positive 1, -0-degree being straight up and down, or true vertical. If it is extreme one way or the other it will cause wear on the inter or outer edge of the tire and possible scallops may appear. This adjustment is for tire wear and possibly some handling, also certain tools such as upper control arm wrench and a tomcat camber adjustment tool may come in handy.There are times when one shim or adjustment to move the rear of the control arm outward will give a wheel the proper setting if one understands what that move will do for both settings (caster and camber) simultaneously. That knowledge or understanding plus the proper hand tools and some experience is all that is really needed. Well, maybe a good coach would come in handy. However, back to the move made by the adding a single shim to the rear of the upper control arm (by the way shims vary in thickness) would give less negative caster and more positive camber. I hope this helps! Any questions? Lem Boydhttp://www.uniquetoolsaccessories.com

Laser Wheel Alignment: Chassis Mounted Vs Wheel Mounted


Best Auto Body Shop in New Jersey